![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Mar 2005
Location: Grapevine, TX
Posts: 3
|
Corvette wheel in 72 C10
I picked up a 3 spoke rally wheel on the cheap and now trying to find out how to adapt it to my stock stearing column. Let me know if you have any pointers?
thanks |
![]() |
![]() |
![]() |
#2 |
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,477
|
Re: Corvette wheel in 72 C10
1st.
![]() ![]() 2nd - Does it look anything like this one pictured below?
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Mar 2005
Location: Grapevine, TX
Posts: 3
|
Re: Corvette wheel in 72 C10
Thats the one. What adapter did you use to make it fit and where did you get it??
thanks, |
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: Sep 2004
Location: Wakaw, Sask, Canada
Posts: 3,180
|
Re: Corvette wheel in 72 C10
Apparently a 69 Camaro hub kit will work on our columns, and I was told that a 68 Camaro hub will work as well, and match the size of the column better. That being said, I mentioned this on the board awhile ago and IIRC someone had tried the 68 hub and ecountered problems. Hopefully they will chime in and set the record straight.
__________________
"You can take the man out of PA, but you can't take PA out of the man" |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Feb 2004
Location: Tacoma WA
Posts: 1,365
|
Re: Corvette wheel in 72 C10
I have never had a problem using the 69+ hubs (genuine GM) that I find at the junk yard. The 68 Camaro hub that I bought (a repro) has issues. I don't know if the issues are because it is a 68 or because it is a repop. It doesn't seem to go down on the shaft far enough to fit nicely.
The 69+ hubs are only a little bigger in diameter at the bottom. When installed they are about 1/8th inch larger than the column (hardly noticeable). Hubs are readily available from Camaro or Chevelle repop vendors along with the horn contact and center cap.
__________________
67 C-20 LWB, tilt, speed alert, vac, 454, T400 67 C-10 SWB, factory air with more to follow |
![]() |
![]() |
![]() |
#6 |
Out of the carpool lane.
Join Date: Jan 2000
Location: Clark Co, WA
Posts: 5,673
|
Re: Corvette wheel in 72 C10
I have an extra hub for a Camaro if anyone would like it for the cost of shipping. I don't know what year it is but I could find out specific dimensions if needed. Years ago I bought a Grant wheel that had been on a Camaro and the hub came with it. I have NO desire to put a Grant wheel on MY Camaro!
![]()
__________________
1968 C-10 SWB, 5.7 Vortec/700R4/3.73 posi, Torch Red 1968 Camaro, 250/Powerglide, all original (No, I'm not gonna drop a 350 in it!...Jeez!) 2000 Honda VFR in the faster yellow! 2008 Husqvarna TE-610 1967 C-10 SWB 'Six Appeal'-Gone but not forgotten... |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Feb 2004
Location: Tacoma WA
Posts: 1,365
|
Re: Corvette wheel in 72 C10
Brad - Is it a GM hub or a Grant hub?
__________________
67 C-20 LWB, tilt, speed alert, vac, 454, T400 67 C-10 SWB, factory air with more to follow |
![]() |
![]() |
![]() |
Bookmarks |
|
|