? Installing 90's Cheyenne seat in 67-72 ? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Zumo · 01-25-2007, 10:42 AM

I haven't realy looked at it yet but is this a "bolt in" type of deal or will I need to drill holes? Ad brackets?
I just picked up a 60/40 bench and want to install it this weekend.
Thanks in advance

454_72_4X4 · 01-25-2007, 11:40 AM

The 60/40 won't be a complete bolt in but it shouldn't be to hard. The inner bracket on the 60 part of the seat will be the biggest headache. You might have to build some spacers, or worst case, you might have to shorten the bracke on the seat. Depending on which truck has the taller trans tunnel.
The outside brackets should be a "just drill the holes" deal.
I have a 88-94 bench seat in my 72. IIRC I just drilled 2 new holes for it.

Post up some pics when ya do your 60/40.

I've got a 99 60/40 spotted I'd like to swap into my 72.

Zumo · 01-25-2007, 11:49 AM

That's waht I am curious about. The shorter brack on the "60" seat. I wonder if I could get another bracket like the tall one and get it to fit.

454_72_4X4 · 01-25-2007, 11:56 AM

I think the taller bracket would bolt onto the seat but then it'd probably be to tall

454_72_4X4 · 01-25-2007, 11:58 AM

Does your 68 have a "high hump" or "low hump" trans tunnel?

whatnow123 · 01-25-2007, 12:09 PM

If you could take a couple of pictures and do a write up about the process that would be awesome as I just picked up some 04 Silverado Seats. Mine are 40/20/40 with a center arm rest. The middle section fits over the hump perfect but I'm wondering about the rear brackets on the buckets. I tossed mine in there just to check fit (I'm pretty far from installing them currently) and seems like it's not going to be too much trouble.

Zumo · 01-25-2007, 12:46 PM

Quote:

Originally Posted by 454_72_4X4

Does your 68 have a "high hump" or "low hump" trans tunnel?

Low hump right? Since it 2wd.

I will try to get some pics of my efforts as well.

rodstored-72 · 01-25-2007, 03:57 PM

i too would love to see a write up on this as well.. i am currently looking to do the same & was wanting to know what i would be looking at in the case of mods needed to make it work...

thanks!
rodstored-72

jimmydean · 01-25-2007, 03:58 PM

I used 4 washers for the front bolt of the 60 seat and my seat sits about perfect. Without it, it looked ok, but was just a little lower than the other seat.

Zumo · 01-25-2007, 04:55 PM

Thanks Jimmy, I'll be somewhat prepaired.

01-25-2007, 10:42 AM	#1
Zumo Hot Rods For Life Join Date: Sep 2001 Location: Waxahachie, TX Posts: 3,305	? Installing 90's Cheyenne seat in 67-72 ? I haven't realy looked at it yet but is this a "bolt in" type of deal or will I need to drill holes? Ad brackets? I just picked up a 60/40 bench and want to install it this weekend. Thanks in advance __________________ 1968 C10 LWB **SOLD* Andy Viva Los Bicicletas! Los Muertos Custom Bicycles

01-25-2007, 11:40 AM	#2
454_72_4X4 Registered User Join Date: Apr 2004 Location: N.E. MO Posts: 1,749	Re: ? Installing 90's Cheyenne seat in 67-72 ? The 60/40 won't be a complete bolt in but it shouldn't be to hard. The inner bracket on the 60 part of the seat will be the biggest headache. You might have to build some spacers, or worst case, you might have to shorten the bracke on the seat. Depending on which truck has the taller trans tunnel. The outside brackets should be a "just drill the holes" deal. I have a 88-94 bench seat in my 72. IIRC I just drilled 2 new holes for it. Post up some pics when ya do your 60/40. I've got a 99 60/40 spotted I'd like to swap into my 72. __________________ 72 C20 4X4 454 4 speed 89 Trans Am (was) 305 TPI 700r4 93 C1500 2wd Extended cab 350 700r4 98 Sonoma (TPI outa the Trans Am) 03 Yamaha 660 Raptor 03/04 660 Raptor 07 700 Raptor 85 Honda Odyssey

01-25-2007, 11:49 AM	#3
Zumo Hot Rods For Life Join Date: Sep 2001 Location: Waxahachie, TX Posts: 3,305	Re: ? Installing 90's Cheyenne seat in 67-72 ? That's waht I am curious about. The shorter brack on the "60" seat. I wonder if I could get another bracket like the tall one and get it to fit. __________________ 1968 C10 LWB **SOLD* Andy Viva Los Bicicletas! Los Muertos Custom Bicycles

01-25-2007, 11:56 AM	#4
454_72_4X4 Registered User Join Date: Apr 2004 Location: N.E. MO Posts: 1,749	Re: ? Installing 90's Cheyenne seat in 67-72 ? I think the taller bracket would bolt onto the seat but then it'd probably be to tall __________________ 72 C20 4X4 454 4 speed 89 Trans Am (was) 305 TPI 700r4 93 C1500 2wd Extended cab 350 700r4 98 Sonoma (TPI outa the Trans Am) 03 Yamaha 660 Raptor 03/04 660 Raptor 07 700 Raptor 85 Honda Odyssey

01-25-2007, 11:58 AM	#5
454_72_4X4 Registered User Join Date: Apr 2004 Location: N.E. MO Posts: 1,749	Re: ? Installing 90's Cheyenne seat in 67-72 ? Does your 68 have a "high hump" or "low hump" trans tunnel? __________________ 72 C20 4X4 454 4 speed 89 Trans Am (was) 305 TPI 700r4 93 C1500 2wd Extended cab 350 700r4 98 Sonoma (TPI outa the Trans Am) 03 Yamaha 660 Raptor 03/04 660 Raptor 07 700 Raptor 85 Honda Odyssey

01-25-2007, 12:09 PM	#6
whatnow123 Registered User Join Date: Oct 2006 Location: Arizona Posts: 835	Re: ? Installing 90's Cheyenne seat in 67-72 ? If you could take a couple of pictures and do a write up about the process that would be awesome as I just picked up some 04 Silverado Seats. Mine are 40/20/40 with a center arm rest. The middle section fits over the hump perfect but I'm wondering about the rear brackets on the buckets. I tossed mine in there just to check fit (I'm pretty far from installing them currently) and seems like it's not going to be too much trouble.

01-25-2007, 03:57 PM	#8
rodstored-72 chevy truck fan Join Date: Mar 2005 Location: Gilbert, arizona 85298 Posts: 2,009	Re: ? Installing 90's Cheyenne seat in 67-72 ? i too would love to see a write up on this as well.. i am currently looking to do the same & was wanting to know what i would be looking at in the case of mods needed to make it work... thanks! rodstored-72

01-25-2007, 03:58 PM	#9
jimmydean Registered User Join Date: May 2005 Location: Beaverton, OR Posts: 3,728	Re: ? Installing 90's Cheyenne seat in 67-72 ? I used 4 washers for the front bolt of the 60 seat and my seat sits about perfect. Without it, it looked ok, but was just a little lower than the other seat.

01-25-2007, 04:55 PM	#10
Zumo Hot Rods For Life Join Date: Sep 2001 Location: Waxahachie, TX Posts: 3,305	Re: ? Installing 90's Cheyenne seat in 67-72 ? Thanks Jimmy, I'll be somewhat prepaired. __________________ 1968 C10 LWB **SOLD* Andy Viva Los Bicicletas! Los Muertos Custom Bicycles



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.