Keeping it clean inside once it's done... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Mt Man Chad · 02-01-2007, 05:43 PM

I'm going over the small body panels in prep for primer, inner doors for new door skins, tail gate. I took the bed out getting acid dipped so I'll be shooting that in next week top and bottom.

My question is - on the bed side toolbox doors, I know they are the first thing to rust out. The one I am working with is very clean. What is the best way to clean and seal it so it doesn't rust in the future? In addition the door bottom insides before the skins go on.

bagged91 · 02-02-2007, 07:12 PM

Can't really say on the toolbox door (never really looked at one before) but I would say the best thing for the inside of the panels you don't want to rot out again is to coat them with POR-15 or something equivelent... Try asking over in the paint & body section. Someone over there may be able to help better... Solid looking GMC ya got there!

L8R - Joe

GREASEMONKEY72 · 02-03-2007, 08:21 AM

first off, nice truck you got there

but also i think you could also roll on or spray some line-ex or rhino lining or others of the sort for protection to

02-01-2007, 05:43 PM	#1
Mt Man Chad Registered User Join Date: Oct 2006 Location: Oakridge Oregon Posts: 1,865	Bedside Toolbox doors.... I'm going over the small body panels in prep for primer, inner doors for new door skins, tail gate. I took the bed out getting acid dipped so I'll be shooting that in next week top and bottom. My question is - on the bed side toolbox doors, I know they are the first thing to rust out. The one I am working with is very clean. What is the best way to clean and seal it so it doesn't rust in the future? In addition the door bottom insides before the skins go on. Attached Images __________________ 68 CST SWB - Gold/White 50th anniversary /TH350/Buddy Buckets/3.73 Posi/dogdish caps. 68 K10 Burb - Gold/White 327/SM465/NP205/3.73 "Daa Burb" build thread Last edited by Mt Man Chad; 02-01-2007 at 05:58 PM.

02-02-2007, 07:12 PM	#2
bagged91 Out draggin' Join Date: Jan 2004 Location: Pitman,NJ Posts: 1,574	Re: Keeping it clean inside once it's done... Can't really say on the toolbox door (never really looked at one before) but I would say the best thing for the inside of the panels you don't want to rot out again is to coat them with POR-15 or something equivelent... Try asking over in the paint & body section. Someone over there may be able to help better... Solid looking GMC ya got there! L8R - Joe __________________ 91 GMC Xcab LB-Bags/bd/caddy clip SOLD 72 C10 Cheyenne Super LWB SOLD 92 GMC K1500 Burb 72 C10 Burb (ex. Cheesewagon)SOLD 72 C20 Burb parts truck 71 C10 Burb "project"

02-03-2007, 08:21 AM	#3
GREASEMONKEY72 Registered User Join Date: Aug 2006 Location: Bakersfield,CA Posts: 7,893	Re: Keeping it clean inside once it's done... first off, nice truck you got there but also i think you could also roll on or spray some line-ex or rhino lining or others of the sort for protection to __________________ -steven Alte Seele S.S. "Allison" '72 C/10 LWB 350SB/TH350 - DD PITBULL IS NOT A CRIME



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.