Drop Spindle Question !!! - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Chevyrod · 02-04-2007, 02:44 PM

I installed my air ride suspention and I need about three more inches of drop in the front to level the blazer out. I only have bags in the front now and I want to order a set of drop spindles. I have 15" wheels right now and was wondering what kind of clearence problems I will run into with the lower control arms etc. Will I have any problems with a 3" drop spindle or should I use a 2". If I do have a problem with the lower arm how much does it rub and can I grind a little on the lcm to make it work. I really don't want to buy new rims right now and I know you guys have ran into this before. I just need a little help before I order a Set. Here are a few photos that show what I am trying to do.

short step · 02-04-2007, 04:34 PM

with 3"drop the LCA will rub the rims but u can grind enough off just check it on the ground before u drive. they say the 2 1/2 dont rub but i ordered them and they must be 3 got them from GMC Paul
bob

SCOTI · 02-05-2007, 12:04 AM

3" drop spindles will rub wheels that have too much back spacing. Not all 15" wheels will rub & many people seem to assume this as a fact (I'm not calling short step out on his info). Case in point.... my 74 has 3" drop spindles & when I had 15x6.5 (3.5"BS ?) van ralleys there was no rubbing. I installed my 18x8's w/5.25"BS & they rubbed big time.

What size/back-space wheels are you running?

Chevyrod · 02-05-2007, 05:23 PM

SCOTI,
I JUST WENT OUT AND MEASURED IT, THEY LOOK TO BE 15X8 WITH A 3 1/2" BACKSPACING IF I MEASURED RIGHT. I MEASURED FROM THE MOUNTING SURFACE TO THE OUTER WHEEL LIP. THESE WHEELS WERE ON THE BLAZER WHEN I PURCHASED IT, SO I DON'T NO ALOT ABOUT THEM. IF I MEASURED WRONG LET ME KNOW. I JUST NEED SOME HELP BEFORE I ORDER MY SPINDLES. THANKS AGAIN.

ALSO I TOOK YOUR ADVICE AND WENT WITH THE SHOCKWAVES FROM ART ON THE REAR OF THE BLAZER THEY FIT PERFECT.

02-04-2007, 02:44 PM	#1
Chevyrod Registered User Join Date: Jan 2006 Location: florida Posts: 170	Drop Spindle Question !!! I installed my air ride suspention and I need about three more inches of drop in the front to level the blazer out. I only have bags in the front now and I want to order a set of drop spindles. I have 15" wheels right now and was wondering what kind of clearence problems I will run into with the lower control arms etc. Will I have any problems with a 3" drop spindle or should I use a 2". If I do have a problem with the lower arm how much does it rub and can I grind a little on the lcm to make it work. I really don't want to buy new rims right now and I know you guys have ran into this before. I just need a little help before I order a Set. Here are a few photos that show what I am trying to do. Attached Images

02-04-2007, 04:34 PM	#2
short step Registered User Join Date: Dec 2002 Location: Ludlow,MA Posts: 145	Re: Drop Spindle Question !!! with 3"drop the LCA will rub the rims but u can grind enough off just check it on the ground before u drive. they say the 2 1/2 dont rub but i ordered them and they must be 3 got them from GMC Paul bob

02-05-2007, 12:04 AM	#3
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,064	Re: Drop Spindle Question !!! 3" drop spindles will rub wheels that have too much back spacing. Not all 15" wheels will rub & many people seem to assume this as a fact (I'm not calling short step out on his info). Case in point.... my 74 has 3" drop spindles & when I had 15x6.5 (3.5"BS ?) van ralleys there was no rubbing. I installed my 18x8's w/5.25"BS & they rubbed big time. What size/back-space wheels are you running? __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.* Last edited by SCOTI; 02-05-2007 at 12:06 AM.

02-05-2007, 05:23 PM	#4
Chevyrod Registered User Join Date: Jan 2006 Location: florida Posts: 170	Re: Drop Spindle Question !!! SCOTI, I JUST WENT OUT AND MEASURED IT, THEY LOOK TO BE 15X8 WITH A 3 1/2" BACKSPACING IF I MEASURED RIGHT. I MEASURED FROM THE MOUNTING SURFACE TO THE OUTER WHEEL LIP. THESE WHEELS WERE ON THE BLAZER WHEN I PURCHASED IT, SO I DON'T NO ALOT ABOUT THEM. IF I MEASURED WRONG LET ME KNOW. I JUST NEED SOME HELP BEFORE I ORDER MY SPINDLES. THANKS AGAIN. ALSO I TOOK YOUR ADVICE AND WENT WITH THE SHOCKWAVES FROM ART ON THE REAR OF THE BLAZER THEY FIT PERFECT.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.