Edited by Moderator - The 1947 - Present Chevrolet & GMC Truck Message Board Network

b.sharp · 02-13-2007, 12:56 PM

Edited by Moderator

jds319 · 02-13-2007, 01:47 PM

You and me both.

Houston54 · 02-13-2007, 02:03 PM

The doors on 1955 through 58 are identical. You should be able to trip over these at swap meets or ebay.

jds319 · 02-13-2007, 02:10 PM

1955 to 1959 are identical. Driver's side doors, however, are becoming harder to come by.

b.sharp · 02-13-2007, 02:39 PM

Well, I have two and neither one is very good. I could skin either if they make a skin for them. One needs the bottom inner panel and hinge pocket but appears to have some sort of patch over th original skin already at the bottom. The other I haven't looked at closely. It was in the bed of the truck whe I bought it. I assume it is bad, it has no hinges on it. I haven't seen any around my swap meets here in KY. What does a good door go for as far as cost?

Thanks again.

Kabwe · 02-13-2007, 04:00 PM

Quote:

Originally Posted by b.sharp

Well, I have two and neither one is very good. I could skin either if they make a skin for them. One needs the bottom inner panel and hinge pocket but appears to have some sort of patch over th original skin already at the bottom. The other I haven't looked at closely. It was in the bed of the truck whe I bought it. I assume it is bad, it has no hinges on it. I haven't seen any around my swap meets here in KY. What does a good door go for as far as cost?

Thanks again.

You can buy the skins from brothers I just done this. inside and out. Now for the hinge that is a separate piece so make sure you order it. I had to do both doors and I really did not like the skins for the outside (seem a little thin to me) so I modified them. I only used the bottom and the side and I went a brought some 18 gauge sheet and and and filled it in. The inner patch panel is great please do not get the short one and try to save money its not worth it, get the larger inner panel and replace the whole thing its just a nicer patch panel. I did both of my doors , but my doors were toast. I had to buy 2 outter skins, 2 inner skins, and 2 hinge supports. With a little filler I should be good to go.

krue · 02-13-2007, 04:54 PM

You need to subscribe and post a WTB on the parts board (if the info above doesn't work for you). For info on subscribing, click the support the board link in my signature.

02-13-2007, 12:56 PM	#1
b.sharp Registered User Join Date: May 2006 Location: Frankfort, Kentucky Posts: 508	Edited by Moderator Edited by Moderator Last edited by krue; 02-13-2007 at 04:53 PM.

02-13-2007, 01:47 PM	#2
jds319 Registered User Join Date: Aug 2006 Location: Dallas, Texas Posts: 123	Re: Driver door needed You and me both. __________________ 1956 Chevrolet 1500 Task Force 2002 Texas Aggie Project Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=212633

02-13-2007, 02:03 PM	#3
Houston54 Registered User Join Date: Feb 2005 Location: location Posts: 527	Re: Driver door needed The doors on 1955 through 58 are identical. You should be able to trip over these at swap meets or ebay.

02-13-2007, 02:10 PM	#4
jds319 Registered User Join Date: Aug 2006 Location: Dallas, Texas Posts: 123	Re: Driver door needed 1955 to 1959 are identical. Driver's side doors, however, are becoming harder to come by. __________________ 1956 Chevrolet 1500 Task Force 2002 Texas Aggie Project Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=212633

02-13-2007, 02:39 PM	#5
b.sharp Registered User Join Date: May 2006 Location: Frankfort, Kentucky Posts: 508	Re: Driver door needed Well, I have two and neither one is very good. I could skin either if they make a skin for them. One needs the bottom inner panel and hinge pocket but appears to have some sort of patch over th original skin already at the bottom. The other I haven't looked at closely. It was in the bed of the truck whe I bought it. I assume it is bad, it has no hinges on it. I haven't seen any around my swap meets here in KY. What does a good door go for as far as cost? Thanks again.

02-13-2007, 04:54 PM	#7
krue Designated A-hole! Join Date: Mar 2003 Location: South Mississippi Posts: 36,448	Re: Edited by Moderator You need to subscribe and post a WTB on the parts board (if the info above doesn't work for you). For info on subscribing, click the support the board link in my signature. __________________ "If it ain't broke, fix it 'til it is!" Being stupid ain't illegal. We're Still Debt Free Except for the House!!! www.daveramsey.com 70 GMC SWB Stepside project "Green Booger" soon to be 6.0l/4l80e 93 S-10 "Poppaw's Truck"



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.