glovebox emblem install? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

BUXMAN66 · 11-16-2002, 05:35 PM

got a new emblem for my '68 to put on the glove box door.mine didn't have one,or at least someone took it off at some time and filled in the mounting holes.does any one have a interior pic to show exact placement?also, if anyone has a 67 or 68,how is the studs on the emblem mounted to the gloove box door? the door itself is a double wall,outside skin and the inside is thicker.the emblem itself has two studs on it which tells me it's installed w/ jam nuts.how do you gain access to the inside of the door?the lower lip of the g.b. door has the full length hinge, is it under there? if i remember right the emblem goes along the bottom,right?thanks all!

toms68cst · 11-16-2002, 06:37 PM

I had some pictures on my webshots site but I can't bring it up now for some reason. I can take some measurements later if you want. If you don't have holes I'd use double-sided tape. I replaced mine a few years ago and couldn't get the original type fittings to work out. It's held up since then.

BUXMAN66 · 11-17-2002, 12:52 PM

what is the location for the emblem on the glove box door?lower edge,to the right ,center..........etc.think i'll just have to grind off the studs on the back and go w/the tape

mikep · 11-17-2002, 01:58 PM

2 inches up from the highest point of the lip. 1 3/4" inches from the highest point of the lip on the right side to the widest point of the emblem on top. I used weatherstripping adhesive.

BUXMAN66 · 11-17-2002, 02:13 PM

thanks mike!!

BUXMAN66 · 11-17-2002, 09:36 PM

btw mike,did you place the emblem in the factory location?like you replaced your old one from same location?thanks!

mikep · 11-17-2002, 09:44 PM

Thats the factory location. I had the holes in the glove box door and the old emblem was broken off and under the seat when I got the truck. Whoever owned this truck before didnt throw ANYTHING away!

Looking at that picture now I guess I should have cleaned it up a bit before I took the picture. Its got my 3 year old sons greasy paw prints all over it.

BUXMAN66 · 11-17-2002, 09:48 PM

thanks again mike for the info. 'preciate it ! later, buxman.

Hooter · 11-18-2002, 12:29 AM

how is it holded on? I always wondered are there screws in the back or something? or is it just glue?

BUXMAN66 · 11-18-2002, 02:17 AM

i think the factory emblem's used studs from off the back-side of 'em into holes in your glovebox door and secured 'em w/ jamnuts. i have no idea how you'd access the inner part of the door to run the jamnuts on though.guess i'll be usin' 2 sided tape.

alta-aj · 11-18-2002, 03:11 AM

It had 3 studs on it bu t was onlt 'press fit" I used a screwdriver and gently pryed it off.

11-16-2002, 05:35 PM	#1
BUXMAN66 go bucks! Join Date: Jan 2002 Location: MIAMISBURG OHIO USA Posts: 803	glovebox emblem install? got a new emblem for my '68 to put on the glove box door.mine didn't have one,or at least someone took it off at some time and filled in the mounting holes.does any one have a interior pic to show exact placement?also, if anyone has a 67 or 68,how is the studs on the emblem mounted to the gloove box door? the door itself is a double wall,outside skin and the inside is thicker.the emblem itself has two studs on it which tells me it's installed w/ jam nuts.how do you gain access to the inside of the door?the lower lip of the g.b. door has the full length hinge, is it under there? if i remember right the emblem goes along the bottom,right?thanks all! __________________ '68 swb 1/2t 350/350th '86 lngbd 3/4 TON parts getter '49 gmc 1/2 t 5 window 350/350th '96 gmc sonoma sle ext-cab. hey it's a 4cyl. 5 spd and good on gas y'know?

11-16-2002, 06:37 PM	#2
toms68cst Registered User Join Date: Jun 2000 Location: Bismarck, ND Posts: 4,296	I had some pictures on my webshots site but I can't bring it up now for some reason. I can take some measurements later if you want. If you don't have holes I'd use double-sided tape. I replaced mine a few years ago and couldn't get the original type fittings to work out. It's held up since then. __________________ Unrestored 68 C-10 CST. Original 327. 4-Speed CH465. 50k or so miles. TREASURER, Drum Brake Club.

11-17-2002, 01:58 PM	#4
mikep Used to have a truck Join Date: May 2002 Location: port orchard WA Posts: 1,552	2 inches up from the highest point of the lip. 1 3/4" inches from the highest point of the lip on the right side to the widest point of the emblem on top. I used weatherstripping adhesive. Attached Images __________________ No truck :-(

11-17-2002, 09:44 PM	#7
mikep Used to have a truck Join Date: May 2002 Location: port orchard WA Posts: 1,552	Thats the factory location. I had the holes in the glove box door and the old emblem was broken off and under the seat when I got the truck. Whoever owned this truck before didnt throw ANYTHING away! Looking at that picture now I guess I should have cleaned it up a bit before I took the picture. Its got my 3 year old sons greasy paw prints all over it. __________________ No truck :-( Last edited by mikep; 11-17-2002 at 09:47 PM.

11-17-2002, 09:48 PM	#8
BUXMAN66 go bucks! Join Date: Jan 2002 Location: MIAMISBURG OHIO USA Posts: 803	thanks again mike for the info. 'preciate it ! later, buxman. __________________ '68 swb 1/2t 350/350th '86 lngbd 3/4 TON parts getter '49 gmc 1/2 t 5 window 350/350th '96 gmc sonoma sle ext-cab. hey it's a 4cyl. 5 spd and good on gas y'know?

11-17-2002, 12:52 PM	#3
BUXMAN66 go bucks! Join Date: Jan 2002 Location: MIAMISBURG OHIO USA Posts: 803	what is the location for the emblem on the glove box door?lower edge,to the right ,center..........etc.think i'll just have to grind off the studs on the back and go w/the tape

11-17-2002, 02:13 PM	#5
BUXMAN66 go bucks! Join Date: Jan 2002 Location: MIAMISBURG OHIO USA Posts: 803	thanks mike!!

11-17-2002, 09:36 PM	#6
BUXMAN66 go bucks! Join Date: Jan 2002 Location: MIAMISBURG OHIO USA Posts: 803	btw mike,did you place the emblem in the factory location?like you replaced your old one from same location?thanks!

11-18-2002, 12:29 AM	#9
Hooter My other Love Join Date: Aug 2001 Location: Castlegar B.C. Canada Posts: 4,085	how is it holded on? I always wondered are there screws in the back or something? or is it just glue? __________________ Castlegar B.C.The great white North (Canada Eh!) Hooter_5@hotmail.com First generation Monte Carlo club pictures of my life

11-18-2002, 02:17 AM	#10
BUXMAN66 go bucks! Join Date: Jan 2002 Location: MIAMISBURG OHIO USA Posts: 803	i think the factory emblem's used studs from off the back-side of 'em into holes in your glovebox door and secured 'em w/ jamnuts. i have no idea how you'd access the inner part of the door to run the jamnuts on though.guess i'll be usin' 2 sided tape.

11-18-2002, 03:11 AM	#11
alta-aj Registered User Join Date: Aug 2001 Location: Qualicum Beach, B.C>, Canada Posts: 117	I just took a "Custom" emblem off a glovebox door. It had 3 studs on it bu t was onlt 'press fit" I used a screwdriver and gently pryed it off.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.