66 Short Step roller

[ed455]

My 66 short stepside is for sale. Setup for sbc and 700r4. 3" dual exhaust for header already in place as is driveshaft for the above-mentioned engine tranny comb. New front fenders. New chrome grill and front bumper. Rear roll pan. Bed wood replaced with composite deck wood and polished stainless strips.

Interior is nice with good upholstery, new seat belts with retractable shoulder harness. Aftermarket gauges in billet (SW gauges). New carpet. Kick panel speakers and rear speakers behind seat. Has van tilt steering and completely new wiring harness (EZ wiring) with lots of extra circuits and everything works perfectly. New weather stripping. Side wing windows have been reset with new rubber.

New windshield and sliding rear window.

72 front crossmember and rearend (3.73 non posi) Axle tubes are welded to the center section for strength. Front disk brakes with slotted and cross-drilled rotors. All ne brake lines. 4 core radiator. Torq Thrust II 15x8 wheels with Eagle GTII Tires with about 800 miles on them.

Truck has 2.5" drop front spindles and 4" drop rear springs.

The rockers were replaced by the PO but I'm not crazy about the job he did. The gas tank is in the tool box. The mirror holes have been welded in as has the gas filler hole.

$2500 FIRM

I have WAAAAAAY more into it as you can see from the above discription. Tires and wheels are aboy a $1000 investment in themselves.

Shipping is out of the question. Bring cash and a rollback or trailer.

Oh, when I had the windshield replaced, I found NO RUST and the pinch welds were great. The floors have been properly patched (by me) and the body mounts are great. The front fenders are aftermarket replacements (tri-plus)

[Hart_Rod]

So this needs a motor and tranny and will run?

[ed455]

yep, that's all it needs to be a driver.

[Hart_Rod]

Do you have any underhood pictures? I'd like to see some pics of the rockers also.

[Hart_Rod]

Also, is it a big back window? Do you have the headers for it?

[ed455]

Here's the bed.

Small back window.

No headers.

[ed455]

more pics

[ed455]

one more by request

[Hart_Rod]

Any pictures of the rockers?

[Americanrider]

Data Plate to the glove box.... hmm, Ex-military truck? Sharp looker, Good luck with the sale.

[ed455]

Yep, ex-government vehicle. thought about doing an olive drab on it at one time.

Ed

[ed455]

Additional info:

Has front AND rear aftermarket sway bars.

Has H4 halogen headlights with clear lenses. They really look sharp.

[terrellautosports]

interested in trading for a 2005 dirt modified chassis and parts? everything is worth what you are asking.

[ed455]

Sound like a fun diversion, but I think I'll have to stay away from it. Done the racing thing and enjoyed it too much. It became more important than my ministry so I had to ditch it. Thanks for the offer though.

Things I DO need: a set of nice rims (Torq Thrust, Cragars, aluminm slots, etc.) 15x6, 4.5" BC, and <3.5" back spacing. No peeling or scaling junk please. I can take these as partial trading fodder for this truck. Will also trade for a high quality paint job on another vehicle I have.

[jwart]

interested in trade for paint job. What are you looking to paint/ check out my website-www.art4urhog.com
have friends in henderson that can qualify my paint work. jw

[ed455]

Have a 1965 Rambler 2 door post in beautiful unrestored condition. Has a couple of dings and I want to do a color change.

[ed455]

Also willing to tade for a small pickup in decent condition + cash. Not interested in trading up.

[winston]

Is this truck still for sale? if so could you pm me your phone number please. very interested. thanks winston.

[ed455]

Sorry it took so long to respond. Been away.

I sent you a PM.

[tbish3]

I have a 92 s10. Reg cab, 4cyl, 5spd. Only 97k original miles. I would go my s10 and $500 boot if interested. let me know.

thanks

[ed455]

SOLD yesterday to a local.

Thanks.