suggestions for install of powerbrake booster? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

guf · 06-03-2007, 01:54 AM

i just received a package from ece. new brake booster, master cylinder and valve and lines. i had new brakes installed a few weeks ago and after spending a lot of money i decided i'm going to attempt to do the rest of my work myself. anyone have any words of wisdom. hints, warnings?
thanks

matthufham · 06-03-2007, 02:41 AM

it's all easy. i did my brakes when i was 15 by myself without any guidance. i swapped a 77 booster onto my 72 and lengthened the pushrod with some angle iron bolted to the pedal. running new lines, bolting the new parts together, and bleeding the brakes takes no more than half a day. i'm only 16 now.

**kwmech** · 06-03-2007, 11:36 AM

Quote:

Originally Posted by matthufham

it's all easy. i did my brakes when i was 15 myself without any guidance........................................... and lengthened the pushrod with some angle iron bolted to the pedal.

I would not recommend this at all.

What year truck? and do the parts match the year?

mbgmike · 06-03-2007, 12:16 PM

Quote:

Originally Posted by guf

i just received a package from ece. new brake booster, master cylinder and valve and lines. i had new brakes installed a few weeks ago and after spending a lot of money i decided i'm going to attempt to do the rest of my work myself. anyone have any words of wisdom. hints, warnings?
thanks

Not a hard project to do at all. Bench bleed the mc. You can do it on the vehicle but do it off if new to this. Bolt up the mc to the booster. install all the componnents loose at first. Like the prop valves brackets mc lines etc. They are easy to strip out if using brass prop valves. Once they are all on carefully tighten them down. Then bolt it up to the firewall. Hopefully you have all the correct brackets. Attach all your brake lines,vacuum line, bleed the system and you technically are good to go. Thats the best case.

If having problems after give us a call or email us.

guf · 06-03-2007, 03:39 PM

Quote:

Originally Posted by mbgmike

Not a hard project to do at all. Bench bleed the mc. You can do it on the vehicle but do it off if new to this. Bolt up the mc to the booster. install all the componnents loose at first. Like the prop valves brackets mc lines etc. They are easy to strip out if using brass prop valves. Once they are all on carefully tighten them down. Then bolt it up to the firewall. Hopefully you have all the correct brackets. Attach all your brake lines,vacuum line, bleed the system and you technically are good to go. Thats the best case.

If having problems after give us a call or email us.

thanks! gonna start now. thanks for the suggestions was wondering if i should connect all first then bolt up. i'll keep you guys posted.

casterbuster · 06-03-2007, 03:50 PM

Make sure the rod that goes between the master cylinder and the booster is
3 3/4" long the one that ece sent me was only 2.5" I did realize it until i had to call a tech at ece.

mbgmike · 06-03-2007, 07:08 PM

Yeah we sell extension rods in various lengths to fit most applications.

guf · 06-03-2007, 10:14 PM

can anyone explain why the brake lights are now on? i have everything installed but have not bleed the brakes. is that why? every thing else went pretty smooth. and the vacuums hose can go behind the carb or on the intake some where?

**kwmech** · 06-03-2007, 10:22 PM

If you have a Q-jet, there is a fitting in the back of the base plate where the line hooks to--or supposed to anyways. Brake lamps, re-adjust the switch or check the pedal height. Sounds like it changed when you installed the new rod coming thru the firewall

GMCMAX · 06-03-2007, 10:27 PM

may have to adjust brake light switch, my pedal was lower and wouldn't touch it, you can see the switch in pic 4 under dash, vac line on carb if it has fitting, I went to th e manifold.
http://67-72chevytrucks.com/vboard/s...d.php?t=221598

dave2953 · 06-03-2007, 11:26 PM

I had the same thing happen to me. Although, I didn't realize until after the battery was dead.

guf · 06-03-2007, 11:58 PM

i looked real quick before the sopranos is starting. so when the button is pressed the brake lights are off and when you apply pressure to the brake it lifts up from the button and the lights go on? and because i had to move my drill a new hole one inch lower it is not applying pressure and the brakes are on? is that confusing? thanks guys

06-03-2007, 01:54 AM	#1
guf Registered User Join Date: May 2007 Location: San Francisco, Ca Posts: 30	suggestions for install of powerbrake booster? i just received a package from ece. new brake booster, master cylinder and valve and lines. i had new brakes installed a few weeks ago and after spending a lot of money i decided i'm going to attempt to do the rest of my work myself. anyone have any words of wisdom. hints, warnings? thanks

06-03-2007, 02:41 AM	#2
matthufham Registered User Join Date: Feb 2005 Location: Carl Junction, Missouri Posts: 2,061	Re: suggestions for install of powerbrake booster? it's all easy. i did my brakes when i was 15 by myself without any guidance. i swapped a 77 booster onto my 72 and lengthened the pushrod with some angle iron bolted to the pedal. running new lines, bolting the new parts together, and bleeding the brakes takes no more than half a day. i'm only 16 now.

06-03-2007, 03:50 PM	#6
casterbuster Mejor Que Nada Join Date: Jun 2006 Location: texas Posts: 232	Re: suggestions for install of powerbrake booster? Make sure the rod that goes between the master cylinder and the booster is 3 3/4" long the one that ece sent me was only 2.5" I did realize it until i had to call a tech at ece. __________________ The only thing that separates "Dreams" from "Reality" is TIME and MONEY!!!

06-03-2007, 07:08 PM	#7
mbgmike Registered User Join Date: Aug 2005 Location: Pasadena,Tx /Pto Pta DR Posts: 5,415	Re: suggestions for install of powerbrake booster? Yeah we sell extension rods in various lengths to fit most applications.

06-03-2007, 10:14 PM	#8
guf Registered User Join Date: May 2007 Location: San Francisco, Ca Posts: 30	Re: suggestions for install of powerbrake booster? can anyone explain why the brake lights are now on? i have everything installed but have not bleed the brakes. is that why? every thing else went pretty smooth. and the vacuums hose can go behind the carb or on the intake some where?

06-03-2007, 10:22 PM	#9
kwmech Senior Member Join Date: Mar 2003 Location: Colfax-California Posts: 8,630	Re: suggestions for install of powerbrake booster? If you have a Q-jet, there is a fitting in the back of the base plate where the line hooks to--or supposed to anyways. Brake lamps, re-adjust the switch or check the pedal height. Sounds like it changed when you installed the new rod coming thru the firewall Last edited by kwmech; 06-03-2007 at 10:23 PM.

06-03-2007, 10:27 PM	#10
GMCMAX Active Member Join Date: Jan 2006 Location: Lower Mid-East Ca. Posts: 326	Re: suggestions for install of powerbrake booster? may have to adjust brake light switch, my pedal was lower and wouldn't touch it, you can see the switch in pic 4 under dash, vac line on carb if it has fitting, I went to th e manifold. http://67-72chevytrucks.com/vboard/s...d.php?t=221598 __________________ Never try to teach a pig to sing; it wastes your time and annoys the pig! Gets More Chicks My lugnuts require more torque than your honda makes! 68 GMC, 4X4 conversion w/73 k20 running gear and springs, 350 4spd, 4.10's, D44 powerlok front, 14BFF govlock rear, 33" tires, lifted 4".

06-03-2007, 11:26 PM	#11
dave2953 Dave's not here, man Join Date: Jun 2004 Location: Winder, Georgia Posts: 2,000	Re: suggestions for install of powerbrake booster? I had the same thing happen to me. Although, I didn't realize until after the battery was dead. __________________ - 2014 VW Jetta - 2015 VW Jetta - 1966 Ford F-250

06-03-2007, 11:58 PM	#12
guf Registered User Join Date: May 2007 Location: San Francisco, Ca Posts: 30	Re: suggestions for install of powerbrake booster? i looked real quick before the sopranos is starting. so when the button is pressed the brake lights are off and when you apply pressure to the brake it lifts up from the button and the lights go on? and because i had to move my drill a new hole one inch lower it is not applying pressure and the brakes are on? is that confusing? thanks guys



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.