fleetside bedside panels? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

53lowdown · 06-28-2007, 06:03 PM

Anyone know where to find complete bedside panels for a 62 SWB? I've searched here and looked at the usual places and find only patch panels. I'd like to find the complete panel if possible.

David Flores · 06-28-2007, 06:37 PM

www.usbody.com sells them in fiberglass. That's all that I know of. You should be able to find them near you also.

**slepysal** · 06-28-2007, 06:55 PM

Were are you from ?

62ChevyStep · 06-28-2007, 06:58 PM

Quote:

Originally Posted by 53lowdown

Anyone know where to find complete bedside panels for a 62 SWB? I've searched here and looked at the usual places and find only patch panels. I'd like to find the complete panel if possible.

No reproductions yet that I know of, I had to do a 1500mile round trip to find a decent SWB fleet bed. I have since located at least three SWB fleet beds that they have turned into trailers around me not sure if they would like to sell?

Best of luck

53lowdown · 06-28-2007, 07:22 PM

Quote:

Originally Posted by slepysal

Were are you from ?

Topeka Kansas

wdsteeves · 06-28-2007, 07:32 PM

Jim Carter has LWB panels that you can cut to fit.I bought both sides( 4 pieces ) for my Burb.Part #'s are SM283L left front,SM285R right front, SM285L rear left,SM285R rear right.They are 48x22 for the rear and 53x22 for the front.Same guage as original. www.oldchevytrucks.com -hope this helps.

53lowdown · 06-28-2007, 09:15 PM

Quote:

Originally Posted by wdsteeves

Jim Carter has LWB panels that you can cut to fit.I bought both sides( 4 pieces ) for my Burb.Part #'s are SM283L left front,SM285R right front, SM285L rear left,SM285R rear right.They are 48x22 for the rear and 53x22 for the front.Same guage as original. www.oldchevytrucks.com -hope this helps.

Do those come clear up to the seam? I'm not near my truck right now so can't measure how far up 22 inches comes on the bedside.

Also, do they each reach to the center of the wheel opening? Basically I'm asking if you weld the two pieces together, do you have a complete new bedside?

Frizzle Fry · 06-28-2007, 11:54 PM

Might as well cut down a LWB to SWB. Unless you can't find a decent one, but they are usually pretty easy to find around here.

stepside66 · 06-29-2007, 01:49 AM

damn man I am in wichita and I just sold my 62 that had good bedsides

06-28-2007, 06:03 PM	#1
53lowdown Junior Member Join Date: Feb 2005 Location: topeka, kansas Posts: 258	fleetside bedside panels? Anyone know where to find complete bedside panels for a 62 SWB? I've searched here and looked at the usual places and find only patch panels. I'd like to find the complete panel if possible. __________________ _______________________________________ 62 SWB BBW (under construction) 86 Vette Convertible

06-28-2007, 06:37 PM	#2
David Flores Registered User Join Date: May 2007 Location: Temple Texas Posts: 399	Re: fleetside bedside panels? www.usbody.com sells them in fiberglass. That's all that I know of. You should be able to find them near you also. __________________ 66 c10 swbfs My Build.

06-28-2007, 06:55 PM	#3
slepysal Registered User Join Date: Oct 2006 Location: San Jose NOR*CAL Posts: 3,080	Re: fleetside bedside panels? Were are you from ? __________________ 1960 Apache long bed fleet L6 250 Clifford intake 2 bbl carb. Langdon cast headers with dual exhaust and bellflower tips. T-5 5 speed, power steering and power disc brakes. "Over, Around or through it... "

06-28-2007, 07:32 PM	#6
wdsteeves Registered User Join Date: Apr 2006 Location: Peachland Posts: 106	Re: fleetside bedside panels? Jim Carter has LWB panels that you can cut to fit.I bought both sides( 4 pieces ) for my Burb.Part #'s are SM283L left front,SM285R right front, SM285L rear left,SM285R rear right.They are 48x22 for the rear and 53x22 for the front.Same guage as original. www.oldchevytrucks.com -hope this helps.

06-28-2007, 11:54 PM	#8
Frizzle Fry Registered User Join Date: Aug 2005 Location: Hillsboro Oregon Posts: 6,449	Re: fleetside bedside panels? Might as well cut down a LWB to SWB. Unless you can't find a decent one, but they are usually pretty easy to find around here.

06-29-2007, 01:49 AM	#9
stepside66 Registered User Join Date: Jun 2005 Location: wichita ks Posts: 97	Re: fleetside bedside panels? damn man I am in wichita and I just sold my 62 that had good bedsides __________________ http://i11.photobucket.com/albums/a1.../DSCN20132.jpg



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.