|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
08-26-2007, 08:36 PM
|
#1 |
|
Registered User
Join Date: Oct 2003
Location: Maryville, TN
Posts: 477
|
ujoints won't come off....help
Ihave a 71 chevy with a two piece drive shaft. I got the clips off and actually disconnected the end going into the rearend but I can not get the other to break apart............suggestions??????
|
|
|
|
08-26-2007, 08:51 PM
|
#2 |
|
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
Re: ujoints won't come off....help
I say take it to the pros... no hammers, no beating up sockets, they'll spin it for you and make sure it's ballanced and inspect every piece on there.
I'm the cheapest SOB on here, and I took mine in. |
|
|
|
|
08-26-2007, 09:09 PM
|
#3 |
|
Registered User
Join Date: Jun 2002
Location: Knoxville Tenn.
Posts: 3,058
|
Re: ujoints won't come off....help
Use your vise. Take socket bigger then the cup and put on one side. Take a nut smaller then cup on put on other end. Tighten vise and hit vise jaws with hammer. Tighten more . Repeat with thicker nut until cup is pushed out the other side. Reverse sides with big socket. Take a long socket and put in cup hole over joint shaft. Push out by tighting vise. (No warrenty with above advise
 )
__________________
56 Chevy Bel-Air 2dr. HT (purchased new) 71 Chevy Cheyenne SWB PU (502HO) 65 GMC short bed step--work in progress and my gofer |
|
|
|
|
08-26-2007, 09:23 PM
|
#4 |
|
Registered User
Join Date: Jun 2007
Location: oregon
Posts: 1,069
|
Re: ujoints won't come off....help
Are you removing the driveline u-joints from there yokes?? Or are you haveing a prob. with the slip joint.???
I had a 66 3/4 ton that was so stiffly sprung I think the suspension never flexed enough to allow the slip joint to move! When time came to replace U-joints, the splines on the slip were stuck but good!! I had to mtake it out carrier bearing, front shaft and all. I used a load of penetrating oil and warmed the joint up with a propane torch just until the grease started to ooze out. It finaly gave way and I cleaned it all up n assembled with never sieze. |
|
|
|
|
08-26-2007, 09:25 PM
|
#5 |
|
Msgt USAF Ret
  
Join Date: Jan 2005
Location: Kalamazoo, Michigan
Posts: 8,709
|
Re: ujoints won't come off....help
__________________
VetteVet metallic green 67 stepside 74 corvette convertible 1965 Harley sportster 1995 Harley wide glide Growing old is hell, but it beats the alternative. |
|
|
|
|
08-27-2007, 06:36 AM
|
#6 |
|
Registered User
Join Date: Oct 2003
Location: Maryville, TN
Posts: 477
|
Re: ujoints won't come off....help
thanks for the link, vettevet...........that looks like my problem...........but I can't even get it off...........g
|
|
|
|
|
08-27-2007, 07:37 AM
|
#7 |
|
Senior Member
 
Join Date: Sep 2005
Location: Lewisville, Nc
Posts: 10,233
|
Re: ujoints won't come off....help
spray some pb blaster on it and let it sit for 15 20 mins
__________________
David fuller Ase Certified Mechanic Click here to help support our board!! 1971 Chevy c-10 under going a 4.8l LSx swap Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=421305 2007 Honda Accord my daily 145kmiles 2002 Honda Accord 4 door With 330k(sisters car) 2005 toyota Avalon 228k( brothers car) 2002 Sububran 5.3 245k 2000 Tahoe 5.3l 378 General manager for Marco's Carwash & lube |
|
|
|
|
08-27-2007, 09:43 AM
|
#8 | |
|
Active Member
Join Date: Jul 2007
Location: Centrally located between Houston, Austin and Waco. BCS area.
Posts: 7,947
|
Re: ujoints won't come off....help
Quote:
 And for sure, if you don't have the right tools. Reminds me of a friend of mine and his brother who bought ujoints, a repair manual and went to work to replace their first ujoints. They did it in the driveway in the hot Texas summer. He told me they beat and hammered for 2 hours and finally gave up and took it to the local shop. Guy charged him $20.00 for both joints. Almost as much as the book!!! 
|
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
