|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
09-18-2007, 08:46 AM
|
#26 |
|
Senior Member
Join Date: Dec 2005
Location: TN
Posts: 2,448
|
Re: How much coil to cut? Please help!
I found a way to cut only half. I replaced my control arms with ControlFreaks units and the lower control arm ring has an isolator and does not require the control arm to be properly positioned. I was able to cut it and install it with no problem.
__________________
1947 International KB-1 1957 Chevy Bel-Air riding low 1962 swb fleetside 2002 Chevrolet Silverado 7-inch lift on 35 Daily driver 2016 Chevy Tahoe Better halves ride |
|
|
|
09-18-2007, 04:43 PM
|
#27 |
|
Registered User
Join Date: Sep 2003
Location: Boise ID
Posts: 609
|
Re: How much coil to cut? Please help!
OK I finally got the ball joint to release from the spindle. I have been beating the heck out of the spindle with my 4lb sledge to no avail. A friend talked me into using his pickle fork and it took less than 5 min. no damage to the boot. Thanks for all the info much appreciated!
__________________
"72" Red CORVETTE 4-speed 350 "70" Chevy Short Bed early stages of resto. Edel 600 cfm carb Weiand Stealth Intake HEI shorty Headers 4/2 Drop 295 50R 15 TOYO on 10 inch wide corvette rally rims at all 4 corners. "CHEVY RULES"
|
|
|
|
|
09-18-2007, 06:11 PM
|
#28 |
|
Saving 1 truck at a time!
Join Date: Aug 2001
Location: Kent, WA
Posts: 6,465
|
Re: How much coil to cut? Please help!
I cut two rounds...it rides like a truck...HEY it is a truck...LOL! I am going to bags up front anyway.
__________________
'68 C20 Longhorn 50th Anniversary 400/TH400 '68 C20 Longhorn 50th Anniversary 468/TH400w/buckets '72 C20 Halfhorn (Longhorn w/o cab and front clip) '69 Flxible Cruiser (look up ugly in the dictionary) |
|
|
|
|
09-19-2007, 02:17 AM
|
#29 |
|
Registered User
Join Date: Sep 2003
Location: Boise ID
Posts: 609
|
Re: How much coil to cut? Please help!
stllookn How much room do you have between the bump top and the A-ARM bumper sitting there?
__________________
"72" Red CORVETTE 4-speed 350 "70" Chevy Short Bed early stages of resto. Edel 600 cfm carb Weiand Stealth Intake HEI shorty Headers 4/2 Drop 295 50R 15 TOYO on 10 inch wide corvette rally rims at all 4 corners. "CHEVY RULES"
|
|
|
|
|
09-19-2007, 07:20 AM
|
#30 |
|
67-72 Addict!
Join Date: Feb 2002
Location: The TAX State!
Posts: 7,857
|
Re: How much coil to cut? Please help!
Nothing wrong with cutting more or less than a full coil. I like 1.25 coils for a 3" drop. I never heard of anybody going 2 full rounds though. Stllookn your truck looks great!
__________________
Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads |
|
|
|
|
09-19-2007, 08:56 AM
|
#31 |
|
Senior Member
Join Date: Dec 2005
Location: TN
Posts: 2,448
|
Re: How much coil to cut? Please help!
Yeah, that is a great lookn truck.
I got my truck back together last night, cut 1/2 round and combined with the new a-rms it went from 32.5 to 31. A little dissopointed but whatever it will probably settle. I think with spindles it should look great.
__________________
1947 International KB-1 1957 Chevy Bel-Air riding low 1962 swb fleetside 2002 Chevrolet Silverado 7-inch lift on 35 Daily driver 2016 Chevy Tahoe Better halves ride |
|
|
|
|
09-19-2007, 12:53 PM
|
#32 | |
|
Registered User
Join Date: May 2005
Location: PA
Posts: 2,696
|
Re: How much coil to cut? Please help!
Quote:
|
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
