|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
12-30-2007, 02:17 PM
|
#1 |
|
Registered User
Join Date: Dec 2007
Location: Johnson City TN
Posts: 570
|
73 crossmember in 68???
how hard is it to take the entire front crossmemer from a 73 with disk brakes and put it in a 68.. how does the steering linkage fit up..
what all needs to be changed?? |
|
|
|
12-30-2007, 03:33 PM
|
#2 |
|
Senior Member
Join Date: Nov 2004
Location: Vacaville, CA
Posts: 2,272
|
Re: 73 crossmember in 68???
It will all bolt up with no problems. You will have to drill 2 new holes for the crossmember but otherwise a very easy project. I did it on a 67 CHevy frame using a 79 subframe.
|
|
|
|
|
12-30-2007, 03:39 PM
|
#3 |
|
Registered User
Join Date: Dec 2007
Location: Johnson City TN
Posts: 570
|
Re: 73 crossmember in 68???
no steering linkage modifications???
|
|
|
|
|
12-30-2007, 03:41 PM
|
#4 |
|
Senior Member
Join Date: Nov 2004
Location: Vacaville, CA
Posts: 2,272
|
Re: 73 crossmember in 68???
no, just some drilling and go.
|
|
|
|
|
12-30-2007, 06:01 PM
|
#5 |
|
I am a Referee of life.
Join Date: Jun 2000
Location: Greensboro N.C.
Posts: 13,993
|
Re: 73 crossmember in 68???
The only thing I would add is to use new grade 8 hardware.
__________________
The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil" |
|
|
|
|
12-31-2007, 02:22 AM
|
#6 |
|
Senior Member
Join Date: Apr 2005
Location: Joppa, Maryland
Posts: 4,408
|
Re: 73 crossmember in 68???
I've read on here that most that do this swap, don't even use the 2 holes that don't lien up. I remember removing the front suspension from a 84 burb, and there were a lot of bolts that had to be removed. I plan on doing the same swap in the Spring.
__________________
1997 GMC Sierra Ext 1965 Mustang |
|
|
|
|
12-31-2007, 01:32 PM
|
#7 |
|
Registered User
Join Date: Dec 2007
Location: Johnson City TN
Posts: 570
|
Re: 73 crossmember in 68???
thank you all for your input
|
|
|
|
|
12-31-2007, 03:22 PM
|
#8 |
|
Registered User
Join Date: Apr 2006
Location: Texas
Posts: 259
|
Re: 73 crossmember in 68???
works great - 85ish front member - some after market motor mounts need a hole to be drilled in the crossmember - bolt locations are different
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
