![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Special Order
![]() ![]() Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,859
|
Floor Shift from Van Tilt?
What does it take to make a 4spd floor shift tilt column from a column shift tilt?
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
![]() |
![]() |
![]() |
#2 |
Born Psycho
![]() Join Date: Feb 2001
Location: brentwood,cal,usa
Posts: 4,884
|
Re: Floor Shift from Van Tilt?
Tim,
i got the pieces necessary from an older GM car tilt with a floor shift--the cup where the shift handle was and the upper tin cover. i got lucky finding those pieces but a little JB Weld should fix the shift handle issue and the upper cover is tin so welding/brazing/soldering should be no problem. hope this helps. by the way, i didn't destroy a good column to get the pieces i used, it was already butchered up.
__________________
jerry moss 72 cheyenne super K20- tilt,tach,vacuum,speedwarning,buckets,shoulder belts,am/fm,tow hooks,bumper guards,toolbox,aux. fuel tank,posi front and rear,plus other goodies!!! SOLD 69 suburban K20-tilt,tach,vacuum,speedwarning,buckets,shoulder belts,am/fm,4 inch all spring lift,4 speed, 14 bolt full floater, dana 44 HD,warn winch,posi front and rear,tow hooks,plus other goodies. 73/80 chevy/gmc K20 SB400,turbo 400,205,tilt,a-c,gas hog. 77 K/5 cheyenne blazer-daily driver/beater. SON HAS IT NOW BRENTWOOD,CALIFORNIA |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Dec 2003
Location: here
Posts: 5,789
|
Re: Floor Shift from Van Tilt?
I JB welded my van auto column for a floor shift. Should be about the same thing...
|
![]() |
![]() |
![]() |
#4 |
Post Whore
![]() Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,684
|
Re: Floor Shift from Van Tilt?
Here's a link showing my conversion for my K20. JB weld and I used some cut out pieces from a beer can to help fill in the large areas with JB on top. Sands down real nice.
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
![]() |
![]() |
![]() |
#5 | |
Registered User
Join Date: Dec 2003
Location: here
Posts: 5,789
|
Re: Floor Shift from Van Tilt?
Quote:
|
|
![]() |
![]() |
![]() |
Bookmarks |
|
|