![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Feb 2007
Location: Colorado Springs, Co
Posts: 1,939
|
convert low hump to high
I have this cab out of a 71 cheyenne. Has a low hump with no tunnel bolt on cover. I want to use this cab on a 4x4 frame. Has anyone cut these floors before to be able ti install a 4x4 tunnel cover, and if so, what is best way? ThanksAttachment 332772
Attachment 332773 Last edited by otsenre; 04-05-2008 at 09:55 AM. |
![]() |
![]() |
![]() |
#2 |
Senior Member
![]() Join Date: May 2001
Location: Independence MO.
Posts: 7,698
|
Re: convert low hump to high
Its super easy, you can cut along one of the endentions on the floor. Set your high hump in and mark it, then just cut away!!!
__________________
72 3/4t Custom Deluxe 402/auto 66k Original paint 71 3/4t 4x4 Custom Deluxe 10k original miles Original paint 71 3/4t Cheyenne 402 70k original paint 72 3/4t 4x4 Custom deluxe 72 3/4t 4x4 Custom deluxe 91k original paint 72 Cheyenne/30 Dually 69 Camaro SS396 4-speed 13 GMC 2500HD Duramax I bought new 05 Jeep Wrangler "Willys Edition" 12k miles (I bought new) 85 3/4 ton 4x4 Scottsdale 33k miles original paint 86 1 ton 4x4 SRW Silverado 454 restored 80 1 ton 4x4 SRW Silverado 9,434 original miles!! original paint 95 GMC 1 ton dually 4x4 my dad bought new 95 GMC 3/4 ton 4x4, regular cab 454, 31k original miles 2002 2500HD 4x4 regular cab 6.0L 67k miles 2002 2500HD 4x4 regular cab 8.1L 28k miles 2003 GMC 2500HD 4x4 regular cab Diesel 93k miles 67-72 Parts for sale |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Mar 2006
Location: USA
Posts: 21,020
|
Re: convert low hump to high
I cut mine out with the torch when I used a 2wd cab on my 4wd shortbed chassis.I had the cab off the frame when I did it though.I wouldn't of used the torch if the tranny was in it...I put the 4wd cover on,and sprayed some paint around the outside of it so the bolt holes would be marked...You can tell on the 2wd floor where it needs cut out.
Last edited by 1969k10stepside; 01-30-2008 at 12:11 PM. |
![]() |
![]() |
![]() |
#4 |
Active Member
![]() Join Date: Dec 2003
Location: Waterbury, CT
Posts: 591
|
Re: convert low hump to high
I used a chisel and just cut in the recessed line on the floor. Make sure you use a good sharp chisel and you will get a nice smooth cut line.
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Sep 2004
Location: Pierre SD
Posts: 1,533
|
Re: convert low hump to high
Use a sawzall or jigsaw. Will take a little longer. I used an air chisel when I did mine. Lotsa noise.
__________________
I think the world needs a drink... ![]() Help somebody...If you can....VanZant We're not wrong, we're not sorry, and its probably gonna happen again. That's the truth about men. Tracy Byrd ![]() Member# 13924 '70 c10, 350/350 '68 c10 250/4spd '68 c10 no eng/trans fac ps/pb/ac/at (future father/sons project) '48 Chevy Loadmaster |
![]() |
![]() |
![]() |
#6 |
Registered User
![]() Join Date: Feb 2004
Location: Idaho
Posts: 4,034
|
Re: convert low hump to high
Whow, Chisels, Air Chisels, Torches. Yikes. I like how 69k10 used spray paint to mark the holes. Good idea.
__________________
"Remember, They can Kill You, but they can't eat You, That's against the law!!!!!!!!!" |
![]() |
![]() |
![]() |
Bookmarks |
|
|