Airbagit 2.5" drop spindles up for grabs

[screamin_c10]

I bought these last fall and installed one on screamin to see if they would give me the stance I wanted. I ended up going with a spring drop as the spindles move the tire/wheel combo out 1 inch and I dont have the clearance. they have some very minor surface rust from the Oregon humidity but nothing that wont clean right up. I have the 73-87 upper ball joints and tierod ends to go along with them. I installed one tierod end with the spindle when I mocked it up.

As far as I know these will fit 71-72 C10s with the 1.25 rotor using the 73-87 upper ball joint and outer tie rod end, I'm sure they would fit others years as well with some mods.

Here is the manufacturer link http://airbagit.com/product_info.php...oducts_id=7341

Spindles $125.00 plus the ride SOLD

Ball joints and tie rod ends $60.00 plus the ride

Or the whole shebang for $175.00 plus the ride

The spindles weigh 45 pounds and the tierod end/balljoints weigh just under 10 boxed. (edit)

My Zip is 97051 so you can figure shipping

[bestchevyfan]

Hi, I Have A 69 With A 1984 Chev Front End Under It For The Disk Brakes. Will This Work On This And If So How Much Of A Drop Will It Have.thanks,buddy

[ryan913]

That is a good deal! Post office will send a lot cheaper than UPS. I checked shipping for my zip and the USPS was $22.00 cheaper.

[screamin_c10]

Originally Posted by bestchevyfan

Hi, I Have A 69 With A 1984 Chev Front End Under It For The Disk Brakes. Will This Work On This And If So How Much Of A Drop Will It Have.thanks,buddy

I would assume so IF your 84 front end has the same lower ball joint as the 71-72. I really don't know and can not say for sure though, check with the board, somebody on there is sure to know.

As far as drop goes, they are 2.5' drop spindles

[72BlckButy]

Originally Posted by ryan913

That is a good deal! Post office will send a lot cheaper than UPS. I checked shipping for my zip and the USPS was $22.00 cheaper.

I've had bad experience with USPS for some reason, for my orders I use UPS or FEDex. Things seem to be more easily tracked.

[19stepSide72]

still available?

[screamin_c10]

Originally Posted by 19stepSide72

still available?

Yes they are

[gopackamx]

Interested also.

[DMARCUM123]

if it gets to me let me know

[screamin_c10]

Just an FYI, these are not spoken for.

19stepSide72 your 1st in line

gopackamx your next up

then DMARCUM123

Let me know if your in or out so the next guy in line gets a chance.

[screamin_c10]

Bump

[gopackamx]

If it is my turn e-mail me at gopack343@aol.com and I will take them, thanks

[89 crew]

Originally Posted by 72BlckButy

I've had bad experience with USPS for some reason, for my orders I use UPS or FEDex. Things seem to be more easily tracked.

If you want to have a good experience with usps register the package. A registered package goes in a locked cage all the way from a to b and Any employee that touches the package has to sign on the shipping sheet or they are fired.

[67_C-30]

If the spindles are still available, I'll take them.

[screamin_c10]

Originally Posted by gopackamx

If it is my turn e-mail me at gopack343@aol.com and I will take them, thanks

I haven't heard from the others so your up next...Pm sent

67_c-30 your up next after gopackamx

[gopackamx]

pm sent

[screamin_c10]

PM back at ya...

[screamin_c10]

Spindles are SOLD, Balljoints and tierod ends are still available....