any differential recommendations? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

sickchevy68cst · 02-29-2008, 03:37 AM

im buildin a 496 puttin over 650+ hp and 700 lbs torque backed by a th400 by tci i'm boggled by diff housin selection at a decently good price been lookin up some places but its like 1,300 for a bare case with axles anyone kno anywhere thats cheaper

Lookin for either a 9 in or d60 :FD

1968SWBBigBlock · 02-29-2008, 06:37 AM

Suck it up and spend the bucks on a good set up, you are 80% of the way home go ahead and finish it.
If you run big enough tires and you hook up say good buy to your rear end

Below is from Moser, they will do a nice job for you.

Complete M9 Bolt-In Pkg - Street Application
Package Includes: Mild Steel M9 Bolt-In Housing, 28 or 31 Spline Axles, Assembled Super Light Case, Center Section w/ a Posi, 1310 Nodular Pinion Yoke Pro Street Gears, 1/2” Wheel Studs,
Fill & Drain Plug, All Bearings, Seals and Hardware.
2255

sickchevy68cst · 03-01-2008, 11:47 PM

thnx alot ill look into ive been gettin suggestions to look at moser by everyone

02-29-2008, 03:37 AM	#1
sickchevy68cst Rice Killing 101 Join Date: Feb 2008 Location: aliso viejo California Posts: 107	any differential recommendations? im buildin a 496 puttin over 650+ hp and 700 lbs torque backed by a th400 by tci i'm boggled by diff housin selection at a decently good price been lookin up some places but its like 1,300 for a bare case with axles anyone kno anywhere thats cheaper Lookin for either a 9 in or d60 :FD __________________ distrubin the peace since i got the thing and broke the origianl radio on 95.5 classic rock Ride: 1968 c20 lwb 327(orig motor)/np435/eaton 4.10 w/posi puttin in a 496 rebuilding trans need to rebuild diff :\| need to start takin pics and start a project thread

02-29-2008, 06:37 AM	#2
1968SWBBigBlock Active Member Join Date: Oct 2006 Location: Ohio Posts: 1,643	Re: any differential recommendations? Suck it up and spend the bucks on a good set up, you are 80% of the way home go ahead and finish it. If you run big enough tires and you hook up say good buy to your rear end Below is from Moser, they will do a nice job for you. Complete M9 Bolt-In Pkg - Street Application Package Includes: Mild Steel M9 Bolt-In Housing, 28 or 31 Spline Axles, Assembled Super Light Case, Center Section w/ a Posi, 1310 Nodular Pinion Yoke Pro Street Gears, 1/2” Wheel Studs, Fill & Drain Plug, All Bearings, Seals and Hardware. 2255 __________________ 1968 SWB 454 + .040, 490HP x 540 FT pounds of Torque 10-1 Kb Forged pistons, recon rods w/ ARP wave loc bolts 781 heads Ported with 2.19/1.88 SSTvalves Lunati 60204 cam, Micro Trol lifters, Ported Edelbrock Performer Rpm manifold armor coated, Pertronix Triple Strike Ignition Holley 770 Street Avenger carb,Headers armor coated Built by Watson Ruppel Performance in Sarahsville Ohio. Hardshift Tranny Built Turbo 350,TSI 10" 3000 stall 12 Bolt Eaton Posi 4.10 Richmond Gears moser axles 18.5" x 31" Hoosier Pro Street Radials ET Classic 5 Wheels - polished Power Steering, Power Brakes,Disc Brakes,Tach & Gauge Dash, Tilt,Factory Air (gone) Custom Paint & Body Work Special thanks to my wife, my son and my money tree

03-01-2008, 11:47 PM	#3
sickchevy68cst Rice Killing 101 Join Date: Feb 2008 Location: aliso viejo California Posts: 107	Re: any differential recommendations? thnx alot ill look into ive been gettin suggestions to look at moser by everyone __________________ distrubin the peace since i got the thing and broke the origianl radio on 95.5 classic rock Ride: 1968 c20 lwb 327(orig motor)/np435/eaton 4.10 w/posi puttin in a 496 rebuilding trans need to rebuild diff :\| need to start takin pics and start a project thread



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.