Anybody know the width of stock bench seat? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

chevychase · 05-01-2008, 01:58 AM

I'm looking at a replacement, but not sure if it will fit. If anybody could tell me what the heck the width of the stock bench seat is, I'd sure appreciate it.

Thanks!

68gmsee · 05-01-2008, 02:07 AM

I just put a rear seat from a 90's chevy crew cab on mine and it fit right on.

I have it out in my country property but, I'm almost certain my old seat was 58 inches and the replacement was about the same.

chevychase · 05-01-2008, 02:14 AM

Quote:

Originally Posted by 68gmsee

I just put a rear seat from a 90's chevy crew cab on mine and it fit right on.

I have it out in my country property but, I'm almost certain my old seat was 58 inches and the replacement was about the same.

I wish you had a picture, I'm looking at a rear seat from a '06 Silverado, there 60" wide. Here's a few pics of them:

68gmsee · 05-01-2008, 02:31 AM

Probably won't get out there until Thurs. I'll take a pic then if you still need it. I don't see why 60 inches wouldn't fit. You have a couple inches or so on either side with the stock seat.

The thing you may have to watch out for is the height. Those seats look pretty tall and if you have the stock steering wheel you will be squeezing in. May have to do some mods...

72BlckButy · 05-01-2008, 03:06 AM

If you can give me a couple days... when I get back home I will measure my seat. I just pulled an aftermarket seat out and installed an original seat in. If I remember correctly the seat I pulled out was roughly 5 foot wide, long, whater.... from door to door. Let me know exactly what measurements you need and I will get them for you. Maybe I can convice the wife to check on it for me.

chevychase · 05-01-2008, 03:17 AM

Thanks guys for the offers! The seat I'm looking at is 60" wide overall, I just wanted to make sure it wasn't too wide OR too narrow for my '67. I just need the overall width of the original bench seat to make certain.

Thanks again!

**El Jay** · 05-01-2008, 04:07 AM

I didn't have any body to help me, so I measured from a seam to one edge of the seat; then went around to the other side & measured from the seam to the other edge.
Came up with 58-59 inches.

Hope that helps a bit.

chevychase · 05-01-2008, 04:21 AM

Quote:

Originally Posted by El Jay

I didn't have any body to help me, so I measured from a seam to one edge of the seat; then went around to the other side & measured from the seam to the other edge.
Came up with 58-59 inches.

Hope that helps a bit.

Thanks a bunch for going out of your way and getting that measurment! Looks like the seat should fit!

**El Jay** · 05-01-2008, 05:10 AM

Quote:

Originally Posted by chevychase

Thanks a bunch for going out of your way and getting that measurment! Looks like the seat should fit!

You're welcome. Glad I could help.
That's why we're all here.

FYI, though, I didn't go out of my way. It was simply a matter of walking out to my driveway.

Ever the smart a$$,
El Jay

chevychase · 05-01-2008, 05:18 AM

Quote:

Originally Posted by El Jay

FYI, though, I didn't go out of my way. It was simply a matter of walking out to my driveway.

Well it was cool of you to do so!

Spray-Bomb · 05-01-2008, 08:02 AM

This is what a 88-98 rear seat out of a crew cab looks like in our trucks

It fit good, but just like the stock one its a lil tall to me (prolly cuz Im 6' 3")

chevychase · 05-01-2008, 08:55 AM

Thanks for pics spray-bomb! That gives me a better idea on what they look like.

05-01-2008, 01:58 AM	#1
chevychase Registered User Join Date: Jun 2007 Location: Boca Raton, FL Posts: 478	Anybody know the width of stock bench seat? I'm looking at a replacement, but not sure if it will fit. If anybody could tell me what the heck the width of the stock bench seat is, I'd sure appreciate it. Thanks! __________________ Joe

05-01-2008, 02:07 AM	#2
68gmsee Active Member Join Date: Jul 2007 Location: Centrally located between Houston, Austin and Waco. BCS area. Posts: 7,947	Re: Anybody know the width of stock bench seat? I just put a rear seat from a 90's chevy crew cab on mine and it fit right on. I have it out in my country property but, I'm almost certain my old seat was 58 inches and the replacement was about the same.

05-01-2008, 02:31 AM	#4
68gmsee Active Member Join Date: Jul 2007 Location: Centrally located between Houston, Austin and Waco. BCS area. Posts: 7,947	Re: Anybody know the width of stock bench seat? Probably won't get out there until Thurs. I'll take a pic then if you still need it. I don't see why 60 inches wouldn't fit. You have a couple inches or so on either side with the stock seat. The thing you may have to watch out for is the height. Those seats look pretty tall and if you have the stock steering wheel you will be squeezing in. May have to do some mods...

05-01-2008, 03:06 AM	#5
72BlckButy Tot Roddin' Join Date: Apr 2005 Location: Mid-MO Posts: 24,461	Re: Anybody know the width of stock bench seat? If you can give me a couple days... when I get back home I will measure my seat. I just pulled an aftermarket seat out and installed an original seat in. If I remember correctly the seat I pulled out was roughly 5 foot wide, long, whater.... from door to door. Let me know exactly what measurements you need and I will get them for you. Maybe I can convice the wife to check on it for me. __________________ -Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package) Last edited by 72BlckButy; 05-01-2008 at 03:07 AM.

05-01-2008, 03:17 AM	#6
chevychase Registered User Join Date: Jun 2007 Location: Boca Raton, FL Posts: 478	Re: Anybody know the width of stock bench seat? Thanks guys for the offers! The seat I'm looking at is 60" wide overall, I just wanted to make sure it wasn't too wide OR too narrow for my '67. I just need the overall width of the original bench seat to make certain. Thanks again! __________________ Joe Last edited by chevychase; 05-01-2008 at 03:29 AM.

05-01-2008, 04:07 AM	#7
El Jay Gone to greener pastures Join Date: May 2007 Location: Gateway to the Delta Posts: 7,354	Re: Anybody know the width of stock bench seat? I didn't have any body to help me, so I measured from a seam to one edge of the seat; then went around to the other side & measured from the seam to the other edge. Came up with 58-59 inches. Hope that helps a bit. __________________ '69 Chevy 1/2 T LWB Stepper: Daily Beater '72 GMC 3/4 T Fleet: Another Daily Beater '72 Plymouth Gran Coupe: ? "Ah women. They make the highs higher and the lows more frequent." Friedrich Nietzsche "Never kick a fresh turd on a hot day." Harry S. Truman GUN CONTROL: Never having to say, "I missed you." Always fire two warning shots into your attacker's chest area before putting a bullet between his eyes. Paraphrased from Louis Awerbuck

05-01-2008, 08:02 AM	#11
Spray-Bomb Texas Big Wig Join Date: Jan 2007 Location: Mineola, Texas Posts: 5,620	Re: Anybody know the width of stock bench seat? This is what a 88-98 rear seat out of a crew cab looks like in our trucks It fit good, but just like the stock one its a lil tall to me (prolly cuz Im 6' 3") __________________ Just not low enough... ----------------------------- Sinister Killer

05-01-2008, 08:55 AM	#12
chevychase Registered User Join Date: Jun 2007 Location: Boca Raton, FL Posts: 478	Re: Anybody know the width of stock bench seat? Thanks for pics spray-bomb! That gives me a better idea on what they look like. __________________ Joe



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.