|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
02-03-2003, 11:11 AM
|
#1 |
|
Post Whore
 
Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,683
|
Are there patch panels for these rust areas?
I know I can get a patch panel for the floor, but for the part of the floor that rises up to the dash, is there a replacement panel for that area or do I get to just get some sheetmetal and make it work?
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
|
|
|
02-03-2003, 11:12 AM
|
#2 |
|
Post Whore
Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,683
|
And regarding the cowl area, it does not appear that the replacement patch panels that are available are going to be enough. Is it more sheetmetal work time?
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
|
|
|
|
02-03-2003, 11:13 AM
|
#3 |
|
Post Whore
Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,683
|
View from the outside
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
|
|
|
|
02-03-2003, 11:13 AM
|
#4 |
|
Post Whore
Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,683
|
Outside, side view
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
|
|
|
|
02-03-2003, 11:35 AM
|
#5 |
|
Registered User
Join Date: Oct 2002
Location: Des Moines WA. (Kent, area)
Posts: 668
|
I havent heard of any time to break out the sheet metal. Had to do the same at the seam above the floor pan just used my vice like a sheetmetal brake. good luck looks like your gonna have alot of fun.
__________________
70 chev c10 swb fleet 72 grill, sb 400, 2/4 drop. 68 chev c10 swb fleet Early classic 4/6 drop with 4wheel disc brakes 9"rear 67-8 buckets tilt and A/C Classic GM Truck Club of Washington . |
|
|
|
|
02-03-2003, 12:34 PM
|
#6 | |
|
Senior Member
Join Date: May 2002
Location: Hammond, WI
Posts: 1,795
|
they do make sheetmetal replacement parts for that area. they are the kick panel patches. from LMC, they are 9 inches high from the floor to the top of the patch panel, and 11 inches from the pillar to the top of the angle. they also show to be $17.95 each, you choose the left or right side. hope this helps.
__________________
Mike 2001 Dakota R/T - Silver CC - 1 of 1671 •360 w/46RE •392 limited slip 1972 Chevy Suburban - Turquoise/Black 1969 Chevy C/10 - Blue LWB •350 w/ 700R4 •3.73 posi •PS PB A/C - SOLD  Using your turn signal is not "giving information to the enemy" 67-72 FAQ Quote:
|
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
