Short Bed Frame/67 Cab/Doors/Arizona - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Hotrodhenryj · 06-24-2008, 05:54 PM

This is a short bed frame looks like it is an early 67 because the power stering is shimmed at the frame. It has new upper and lower ball joints, tie rods, control arm bushings, and springs installed about a year ago. Also has new shocks all around, and frame was blasted and painted. New sway bar and bushing was installed in front. Cab is a 67 also and is very nice, 99% rust free. Has small amount is drivers sill under the rubber, and small holes in pass floor next to the sill, pencil size. Both kick panels at floor where the calking goes has some small rust. Inner and outer rockers, cab corners, floors are nice. I have the doors also, they need some body work and some small front corner rust. I have a clear Arizona title. This still has the six lug bolt pattern. I will pull one drum to see if the brakes were also rebuilt as the last owner said they were new. Front and back glass are cracked, very few dings in the cab. Has under dash AC, some holes were drilled for the hoses to access the engine compartment. Looking for 750 for rolling frame, cab and doors. This is a perfect start for that short bed project, lot of the hard work is done. Or take your long bed and put all your nice stuff on this frame, find you a step bed and your set.

If you need more pics let me know and I will post...Thanks, Chuck

teeitup · 06-24-2008, 05:59 PM

Man Chuck I wish I had that cab here in Kansas

Hotrodhenryj · 06-24-2008, 06:00 PM

One more

Hotrodhenryj · 06-24-2008, 06:06 PM

Quote:

Originally Posted by teeitup

Man Chuck I wish I had that cab here in Kansas

Me to and we would both be happy. I swore no more trucks but I have it as bad as you, were both sick!!! If I was your neighbor, my neighbor here would be very happy. I think you get my drift.

*ksjh1316* · 06-24-2008, 06:59 PM

I hate to ask but can you take a pic of how that ps was shimmed I am going to do the same and just need to see how it was done. Man this is a good start for someones project.
Thanks
Jeff

**special-K** · 06-24-2008, 08:22 PM

Heck,Chuck and Randy,You guys are neighbors from where I sit.

If....then....but...so....

Hotrodhenryj · 06-24-2008, 08:36 PM

Quote:

Originally Posted by ksjh1316

I hate to ask but can you take a pic of how that ps was shimmed I am going to do the same and just need to see how it was done. Man this is a good start for someones project.
Thanks
Jeff

Actually shimming is not the correct way to do this. When you put shims in it, it is offset. Its better to heat the frame and dimple it to clear the box. The guy who did this just used body shims.....

chipflyer · 06-24-2008, 09:48 PM

Hey Chuck, you think those two fedex ladies could handle shipping that cab up here?

Jeff

Hotrodhenryj · 06-24-2008, 11:08 PM

Quote:

Originally Posted by chipflyer

Hey Chuck, you think those two fedex ladies could handle shipping that cab up here?

Jeff

LMAO

I guess if I could get it in a box they could handle it. Did your package show up yet?

chipflyer · 06-24-2008, 11:13 PM

Its in Lenexa, about an hour away, should be here tomorrow.

jeff

Hotrodhenryj · 06-25-2008, 05:04 PM

I pulled one wheel and drum, new brakes, new wheel cylinders, new brake hardware, and brake lines. Drums looks new as well as the hub.

Hotrodhenryj · 07-01-2008, 03:49 PM

I have some mixed parts to put a 67 front clip on the truck that would make it complete. Whole truck with two set of doors 1000.

msgross · 07-01-2008, 06:05 PM

only 2380 miles between us....

ttt for you... I would LOOOVE to have that...but of course it's too far...

06-24-2008, 05:54 PM	#1
Hotrodhenryj Truck Farmer Join Date: Nov 2001 Location: Lake Havasu City, Arizona Posts: 1,192	Short Bed Frame/67 Cab/Doors/Arizona This is a short bed frame looks like it is an early 67 because the power stering is shimmed at the frame. It has new upper and lower ball joints, tie rods, control arm bushings, and springs installed about a year ago. Also has new shocks all around, and frame was blasted and painted. New sway bar and bushing was installed in front. Cab is a 67 also and is very nice, 99% rust free. Has small amount is drivers sill under the rubber, and small holes in pass floor next to the sill, pencil size. Both kick panels at floor where the calking goes has some small rust. Inner and outer rockers, cab corners, floors are nice. I have the doors also, they need some body work and some small front corner rust. I have a clear Arizona title. This still has the six lug bolt pattern. I will pull one drum to see if the brakes were also rebuilt as the last owner said they were new. Front and back glass are cracked, very few dings in the cab. Has under dash AC, some holes were drilled for the hoses to access the engine compartment. Looking for 750 for rolling frame, cab and doors. This is a perfect start for that short bed project, lot of the hard work is done. Or take your long bed and put all your nice stuff on this frame, find you a step bed and your set. If you need more pics let me know and I will post...Thanks, Chuck Attached Images __________________ Arizona rust free sheetmetal

06-24-2008, 05:59 PM	#2
teeitup Just like to part out trucks!! Join Date: Nov 2001 Location: Meriden, Ks-North of Topeka 10 miles Posts: 27,395	Re: Short Bed Frame/67 Cab/Doors/Arizona Man Chuck I wish I had that cab here in Kansas __________________ 67 Chev swb stepside 4x4 283 4 speed SOLD 72 blazer 4x4 4 speed Cheyenne 72 GMC swb 4x4 fleet 4 speed, original paint 1958 Cameo (one of 1405 built, it was my dads) 2020 chevy Apex 4x4 crew cab 1969 Z28 with the 302 1980 chevy swb 4x4 1964 chevell Malibu SS 1976 K20, sold new originally out of my dads chevy dealership Members that I've met, over 200 probably closer to 300 in the 12 years I've been on this site, everyone I met "It was a pleasure"

06-24-2008, 06:00 PM	#3
Hotrodhenryj Truck Farmer Join Date: Nov 2001 Location: Lake Havasu City, Arizona Posts: 1,192	Re: Short Bed Frame/67 Cab/Doors/Arizona One more Attached Images __________________ Arizona rust free sheetmetal

06-24-2008, 06:59 PM	#5
ksjh1316 Account Suspended Join Date: Jul 2007 Location: Wichita KS Posts: 1,599	Re: Short Bed Frame/67 Cab/Doors/Arizona I hate to ask but can you take a pic of how that ps was shimmed I am going to do the same and just need to see how it was done. Man this is a good start for someones project. Thanks Jeff

06-24-2008, 08:22 PM	#6
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: Short Bed Frame/67 Cab/Doors/Arizona Heck,Chuck and Randy,You guys are neighbors from where I sit. If....then....but...so.... __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

06-24-2008, 09:48 PM	#8
chipflyer Registered User Join Date: May 2004 Location: Topeka, Ks Posts: 2,293	Re: Short Bed Frame/67 Cab/Doors/Arizona Hey Chuck, you think those two fedex ladies could handle shipping that cab up here? Jeff __________________ I'm not a pessimist, I'm just optimistic that bad things are going to happen. 1971 Cheyenne Super K10 - tilt, cruise, air, am/fm, tow hooks, factory buckets! 1986 Jeep J10 pickup, - 5.3L Vortec with 4L60e and NP241.

06-24-2008, 11:13 PM	#10
chipflyer Registered User Join Date: May 2004 Location: Topeka, Ks Posts: 2,293	Re: Short Bed Frame/67 Cab/Doors/Arizona Its in Lenexa, about an hour away, should be here tomorrow. jeff __________________ I'm not a pessimist, I'm just optimistic that bad things are going to happen. 1971 Cheyenne Super K10 - tilt, cruise, air, am/fm, tow hooks, factory buckets! 1986 Jeep J10 pickup, - 5.3L Vortec with 4L60e and NP241.

06-25-2008, 05:04 PM	#11
Hotrodhenryj Truck Farmer Join Date: Nov 2001 Location: Lake Havasu City, Arizona Posts: 1,192	Re: Short Bed Frame/67 Cab/Doors/Arizona I pulled one wheel and drum, new brakes, new wheel cylinders, new brake hardware, and brake lines. Drums looks new as well as the hub. Attached Images __________________ Arizona rust free sheetmetal

07-01-2008, 03:49 PM	#12
Hotrodhenryj Truck Farmer Join Date: Nov 2001 Location: Lake Havasu City, Arizona Posts: 1,192	Re: Short Bed Frame/67 Cab/Doors/Arizona I have some mixed parts to put a 67 front clip on the truck that would make it complete. Whole truck with two set of doors 1000. __________________ Arizona rust free sheetmetal

07-01-2008, 06:05 PM	#13
msgross Registered User Join Date: Jul 2006 Location: Central PA Posts: 12,201	Re: Short Bed Frame/67 Cab/Doors/Arizona only 2380 miles between us.... ttt for you... I would LOOOVE to have that...but of course it's too far... __________________ The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer" Last edited by msgross; 07-01-2008 at 06:05 PM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.