![]() |
![]() |
#1 |
Big Red & Mister Blue...
Join Date: Jan 2008
Location: Pat, NJ
Posts: 107
|
Clutch question
Does the contact of the clutch with the flywheel bolts cause chatter or any other issues, even remotely?
Thanks.
__________________
K10 1967, SM420 & Rockwell T221 ![]() C1500 1991, 305 CID, Ext Cab, Full Size bed, everything original except air cleaner. |
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: Jul 2001
Location: Muskegon,MI,USA
Posts: 6,026
|
Re: Clutch question
I have not seen the clutch contact the flywheel bolts on any vehicle when properly installed. It should not
contact the bolts. Jim
__________________
1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC |
![]() |
![]() |
![]() |
#3 |
Senior Member
![]() Join Date: Sep 2005
Location: Lewisville, Nc
Posts: 10,234
|
Re: Clutch question
the disc should not touch the bolts if it does the disc is in wrong
__________________
David fuller Ase Certified Mechanic Click here to help support our board!! 1971 Chevy c-10 under going a 4.8l LSx swap Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=421305 2007 Honda Accord my daily 145kmiles 2002 Honda Accord 4 door With 330k(sisters car) 2005 toyota Avalon 228k( brothers car) 2002 Sububran 5.3 245k 2000 Tahoe 5.3l 378 General manager for Marco's Carwash & lube |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Sep 2006
Location: SE Virginia
Posts: 158
|
Re: Clutch question
Could be a bad throw out bearing or pressure plate finger.
__________________
trailers are for boats |
![]() |
![]() |
![]() |
#5 | |
Active Member
![]() Join Date: Jul 2007
Location: Centrally located between Houston, Austin and Waco. BCS area.
Posts: 7,947
|
Re: Clutch question
Quote:
Also, if the clutch has been replaced, the flywheel/pressure plate may not have been resurfaced or resurfaced properly. Or as in my case, a defective clutch disk was the cause. |
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Feb 2006
Location: Smyrna, Ga
Posts: 1,647
|
Re: Clutch question
my throwout bearing makes alittle chatter. it gets wosre as you increase the pressure on it.
|
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Dec 2004
Location: Northern AZ
Posts: 7,271
|
Re: Clutch question
Also clutch facing material can do it, I have a ceramic clutch and if you try to smoothly engage it, it will chatter. In my case it is engaged or not, so I litterally have to dump the clutch every single time, the cops love that by the way! If stocker, I'd be looking to get a new clutch pack and resurface or better yet buy a new OE replacement flywheel (about $75 from Summit) as the old one could be warped, thin, out of round, etc, etc and is probably 40 ish years old, too.
|
![]() |
![]() |
![]() |
Bookmarks |
|
|