|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
07-16-2008, 03:16 PM
|
#1 |
|
Junior Member
Join Date: Jul 2007
Location: Odenton, Md
Posts: 552
|
1970 C-10 Rear Axle Seal?
I have been to parts stores and they all give me axle seals that are to big...anyone know what seals go in there?>
__________________
going to sell this one...looking for a SWB project next. |
|
|
|
07-16-2008, 04:19 PM
|
#2 |
|
Registered User
Join Date: Oct 2005
Location: Overland Park, Ks.
Posts: 5,229
|
Re: 1970 C-10 Rear Axle Seal?
Have you looked at the old ones. Sometimes you can find a number that can be crossed over if they have a different brand. I can look a catalog tomorrow when I get to the shop.
|
|
|
|
|
07-17-2008, 12:58 AM
|
#3 |
|
Registered User
Join Date: Sep 2005
Location: Smith Mountain Lake Virginia
Posts: 1,537
|
Re: 1970 C-10 Rear Axle Seal?
I have a post here about a month old (rear brake job step by step theme) - I think I might have the part numbers if I didn't post them - keep in mind, there are sometimes two numbers, one on each side of the bearing (maybe that was the wheel bearings..) - two trips to the store to figure that one out. I'm done for the night but will try to get the numbers tomorrow if noone else post them.
__________________
"A cat will almost always blink when hit between the eyes with a ball peen hammer" (you don't always have to state the obvious) Wear your PPE! You can eat with false teeth but you can't see with a false eye. 1959 Studebaker Silverhawk 350/400 1972 C10 L6 3OTT 2005 F350 - Built - whew! Last edited by Luvlegs; 07-17-2008 at 12:59 AM. |
|
|
|
|
07-17-2008, 07:12 AM
|
#4 |
|
Junior Member
Join Date: Jul 2007
Location: Odenton, Md
Posts: 552
|
Re: 1970 C-10 Rear Axle Seal?
they were SKF seals...part # 533803
but I cant find them anywhere here. ans no one can cross them over to Federal or NAtional seals. Here are the specs. Shaft 1.618 bore 2.254 OD 2.258 width 0.235
__________________
going to sell this one...looking for a SWB project next. |
|
|
|
|
07-17-2008, 09:11 AM
|
#5 |
|
Registered User
Join Date: Sep 2005
Location: Smith Mountain Lake Virginia
Posts: 1,537
|
Re: 1970 C-10 Rear Axle Seal?
I grabbed the numbers off the seals I have in my truck this morning - got up early even to do it - BUT, they were for the front. I am 98% certain my rears were Mogul and I do know that I got them at advanced auto. Perhaps Advanced can help out?
__________________
"A cat will almost always blink when hit between the eyes with a ball peen hammer" (you don't always have to state the obvious) Wear your PPE! You can eat with false teeth but you can't see with a false eye. 1959 Studebaker Silverhawk 350/400 1972 C10 L6 3OTT 2005 F350 - Built - whew! |
|
|
|
|
07-17-2008, 03:37 PM
|
#6 |
|
Registered User
Join Date: Oct 2005
Location: Overland Park, Ks.
Posts: 5,229
|
Re: 1970 C-10 Rear Axle Seal?
GM axle takes National # 8835S. Spicer axle W/coil springs takes 481837. Spicer axle W/leafs takes 450067. Available at Carquest stores. Sorry I couldn't find any dimensions.
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
