|
07-25-2008, 01:31 PM
|
#1 |
|
Registered User
 
Join Date: Jan 2006
Location: Warrington, PA
Posts: 403
|
rear motor mounts?
I can't figure out how these mount. I think I might have the wrong mounts. Any advice?.....thanks
__________________
 69 C10 LWB GM 350 crate motor, 3.73 rearend
Last edited by rick0312; 07-25-2008 at 01:34 PM. |
|
|
|
07-25-2008, 01:40 PM
|
#2 |
|
Registered User
Join Date: Sep 2005
Location: Canton North carolina
Posts: 3,080
|
Re: rear motor mounts?
they are the supports for the bell housing on straight drive 2wd truck. They are the only mounts on the three speed trans/four speed trans. The piece you showed first goes on top of the cross member and the small piece goes on the bottom and is held in place w/bolt and a three eared lock washer type thing.
__________________
67 blue step side- bb 68 gold and white swb cst anniversary 68 custom swb hot rod Ls swap 69 swb cst 6 cylinder/ overdrive 69 black/black cst bb swb 70 orange and white cst Canada built truck swb bb 71 black and white super swb bb 71 red and white super swb 72 green and white super swb 4x4 62 nova wagon 400 series Ls swapped 68 Camaro 327/4 speed- 1 owner, original paint 66 Volkswagen bettle 69 auto stick Volkswagen Beetle |
|
|
|
|
07-25-2008, 03:35 PM
|
#3 |
|
Registered User
Join Date: Jan 2006
Location: Warrington, PA
Posts: 403
|
Re: rear motor mounts?
they won't fit through the holes on the crossmember. i have the poly bushings.
__________________
69 C10 LWB GM 350 crate motor, 3.73 rearend
|
|
|
|
|
07-25-2008, 04:09 PM
|
#4 |
|
It's a catastrophic success.
Join Date: Jan 2003
Location: Oklahoma
Posts: 2,077
|
Re: rear motor mounts?
The bigger block should saddle the cross member and the little one comes from under with the bolt
|
|
|
|
|
07-25-2008, 04:16 PM
|
#5 |
|
Registered User
Join Date: Jan 2006
Location: Warrington, PA
Posts: 403
|
Re: rear motor mounts?
the center part of the mount is too large for the crossmember holes.......cheap made in china crap!.i paid 50 bucks for these mounts! they are going back.
__________________
69 C10 LWB GM 350 crate motor, 3.73 rearend
Last edited by rick0312; 07-26-2008 at 12:02 AM. |
|
|
|
|
07-25-2008, 04:55 PM
|
#6 |
|
Registered User
Join Date: Jan 2006
Location: Warrington, PA
Posts: 403
|
Re: rear motor mounts?
anybody experience the same problem?
__________________
69 C10 LWB GM 350 crate motor, 3.73 rearend
|
|
|
|
|
07-25-2008, 06:48 PM
|
#7 |
|
Built 4 Speed
Join Date: May 2008
Location: Geneva FL
Posts: 619
|
Re: rear motor mounts?
Whips out Hammer And Drill. They Will Fit
 But in all seriousness that Stinks maybe for a diff year/ wieght class/
__________________
1969 C/10 Short Box: 496/T-56 in worx. "To Be Old And Wise, First You Must Be Young And Stupid" Last edited by d10s69c10; 07-25-2008 at 06:49 PM. |
|
|
|
|
07-25-2008, 08:18 PM
|
#8 |
|
Senior Member
Join Date: Mar 2003
Location: Colfax-California
Posts: 8,630
|
Re: rear motor mounts?
Betcha they sent you the ones for a 4x4 and not the 2wd bellhousing mount
|
|
|
|
|
07-26-2008, 12:06 AM
|
#9 |
|
Registered User
Join Date: Jan 2006
Location: Warrington, PA
Posts: 403
|
Re: rear motor mounts?
they are about a 1/8" larger......I was thinking about drilling the holes bigger, but I wouldn't want to throw the tranny and drive shaft allignment off.
__________________
69 C10 LWB GM 350 crate motor, 3.73 rearend
Last edited by rick0312; 07-26-2008 at 11:41 AM. |
|
|
|
|
08-03-2008, 12:57 AM
|
#10 |
|
Registered User
Join Date: Jan 2006
Location: Warrington, PA
Posts: 403
|
Re: rear motor mounts?
kwmech you were right.....they sent me the 4x4's......thanks for the tip.
__________________
69 C10 LWB GM 350 crate motor, 3.73 rearend
|
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
