|
08-03-2008, 09:33 PM
|
#1 |
|
Registered User
Join Date: Jul 2005
Location: Edgewood, WA
Posts: 899
|
Fender question
Will a 69-72 front fender work on a 68'?
How about the inner fenders? I'm guessing the inners are the same but the outers are differant. Thanks for the help, Dave
__________________
67 C20/ 68 C10 stepside/inline 250--current project 71 GMC 4x4 70 Blazer project-Zombie assault vehicle 67 4x4 Burb 
|
|
|
|
08-03-2008, 09:44 PM
|
#2 |
|
Special Order
  
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,861
|
Re: Fender question
Inners are all the same.The`68 fenders are different from the 69-72s/same as 68-72 GMCs.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
08-03-2008, 10:22 PM
|
#3 |
|
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
Re: Fender question
if you are talkin chevy, you are right.
If you are talkin GMC, it'll work |
|
|
|
|
08-03-2008, 11:38 PM
|
#4 |
|
Junior Member
Join Date: Dec 2006
Location: Southeast Missouri
Posts: 2,436
|
Re: Fender question
I have "Senior Moments" so bare with me.
I have a '67 Chevy that has bad fenders and I have a good set of '69 GMC fenders. Will the '69 GMC fenders fit the '67 Chevy? Thank you. Danny
__________________
'67 Chevy C-20 short stepper - build complete, 454/SM-465. '75 C-30 Single Cab DRW-350 small block/NP-435. '77 GMC-6500 Dump Truck, 427 Tall Deck. '92 GMC K-3500 Duallie, 454/4L80E. |
|
|
|
|
08-03-2008, 11:58 PM
|
#5 |
|
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
Re: Fender question
yes, but there will be marker light holes that aren't needed on the 67, and trim holes won't be right.
But as far as the fender, yes, it'll work |
|
|
|
|
08-04-2008, 07:45 AM
|
#6 |
|
Special Order
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,861
|
Re: Fender question
Shyguy,just so you know (in case you`re having a senior moment) ,only rights fit on right and left on left.OK?
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
08-04-2008, 09:40 AM
|
#7 |
|
Junior Member
Join Date: Dec 2006
Location: Southeast Missouri
Posts: 2,436
|
Re: Fender question
It is early in the day and I have had a couple of cups of coffee so I will be alright for a while. The senior moments seem to come later in the day.
Thank you very much for reminding though that the left and right are not interchangeable. A little off the subject but here goes. I use to have a guy working for me that put duct tape on his shoes and put a L on the left one and R on the right one. He was a professor at a large college before he came to work for me at the shipyard. Danny
__________________
'67 Chevy C-20 short stepper - build complete, 454/SM-465. '75 C-30 Single Cab DRW-350 small block/NP-435. '77 GMC-6500 Dump Truck, 427 Tall Deck. '92 GMC K-3500 Duallie, 454/4L80E. Last edited by Shyguy; 08-04-2008 at 09:42 AM. |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
