|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
09-24-2008, 10:55 PM
|
#1 |
|
Registered User
Join Date: Jul 2008
Location: Vancouver BC
Posts: 448
|
Lower control arm ball joint question
Anyone else have a REALLY hard time pressing these ball joints out? been throwin tool's for half the day trying to get it out. Oxy acetylene tanks were empty
__________________
1978 GMC Jimmy 454bbc Turbo400 NP205 3.73 gears 4inch lift 33's |
|
|
|
09-24-2008, 11:17 PM
|
#2 |
|
Registered User
Join Date: Sep 2008
Location: Seattle Washington
Posts: 22
|
Re: Lower control arm ball joint question
I ended up using a small grinder to cut the rivets on mine
|
|
|
|
|
09-24-2008, 11:22 PM
|
#3 |
|
Registered User
Join Date: Jul 2008
Location: Vancouver BC
Posts: 448
|
Re: Lower control arm ball joint question
the lower's are riveted?
__________________
1978 GMC Jimmy 454bbc Turbo400 NP205 3.73 gears 4inch lift 33's |
|
|
|
|
09-24-2008, 11:23 PM
|
#4 |
|
Registered User
Join Date: Sep 2008
Location: Seattle Washington
Posts: 22
|
Re: Lower control arm ball joint question
My 62 was
|
|
|
|
|
09-25-2008, 01:47 PM
|
#5 |
|
Registered User
Join Date: Dec 2005
Location: Lake Oswego, OR
Posts: 318
|
Re: Lower control arm ball joint question
Same on my 64 C10
|
|
|
|
|
09-26-2008, 03:00 PM
|
#6 |
|
Registerd User
Join Date: Sep 2008
Location: Oklahoma
Posts: 2,118
|
Re: Lower control arm ball joint question
My 65 is a press in. It was stubbern at first so I got a bigger hammer. From what I've seen c10 and c20 are both press in lowers and bolt in uppers.
|
|
|
|
|
09-26-2008, 09:27 PM
|
#8 |
|
Registered User
Join Date: Jul 2008
Location: Vancouver BC
Posts: 448
|
Re: Lower control arm ball joint question
thanks!
__________________
1978 GMC Jimmy 454bbc Turbo400 NP205 3.73 gears 4inch lift 33's |
|
|
|
|
09-27-2008, 12:53 AM
|
#9 |
|
KOFFIN DRAGGER
Join Date: Jan 2008
Location: st.anthony Idaho
Posts: 864
|
Re: Lower control arm ball joint question
I hit both of mine less than 5 times each with a 3lb sledge hammer and they fell out. When in doubt, get a bigger hammer. Your not going to hurt the control arm, whack the s**t out of it.
__________________
If the life I live dont kill me, then I guess I'll never die! New updated stuff at www.kdrodworks.com My site still needs help, web guys and gals pm me. the best guys in the whole world: sweet70beast, jonzcustomshop, runninlow, captainfab, and the one I havent met yet, joe231 |
|
|
|
|
09-27-2008, 02:10 AM
|
#10 |
|
65 - Chevy C10
Join Date: Jun 2006
Location: Los Angeles, CA
Posts: 625
|
Re: Lower control arm ball joint question
true! the only thing is that our were probably never detached so its gonna take more than 5 wacks!
|
|
|
|
|
09-27-2008, 10:02 AM
|
#11 |
|
KOFFIN DRAGGER
Join Date: Jan 2008
Location: st.anthony Idaho
Posts: 864
|
Re: Lower control arm ball joint question
I know the upper had been changed, not sure about the lower. I supported the control arm with 2 floor jacks, 1 inside the arm towards center and 1 outside at the edge. Now when I say "5 whacks" we are talkin full swing man whacks hitting the stud part as hard as possable. I am 265lbs, I can whack something pretty hard. I also had the front clip off the truck, so I kinda cheated.
__________________
If the life I live dont kill me, then I guess I'll never die! New updated stuff at www.kdrodworks.com My site still needs help, web guys and gals pm me. the best guys in the whole world: sweet70beast, jonzcustomshop, runninlow, captainfab, and the one I havent met yet, joe231 |
|
|
|
|
09-27-2008, 02:32 PM
|
#12 |
|
Registered User
Join Date: Jul 2008
Location: Vancouver BC
Posts: 448
|
Re: Lower control arm ball joint question
Haha, well, stupid me, dident read the instruction's on the ball joint press tool (Im a guy, i geuss its in my blood) and i was using the wrong fitting and doing it from the wrong side! both lower's are out and waiting for the new front end rebuild to come in the mail! thanks for the info everyone
__________________
1978 GMC Jimmy 454bbc Turbo400 NP205 3.73 gears 4inch lift 33's |
|
|
|
|
09-27-2008, 09:10 PM
|
#13 |
|
Resistance is Futile
Join Date: Dec 2006
Location: Mesa,Arizona
Posts: 3,519
|
Re: Lower control arm ball joint question
I used one of the large C-clamp deals to remove my ball joints but could not get them back in using the same tool. Had to use a press.... mite have been easier if the control arms were mounted; in case you have trouble.
__________________
64 CHEVY PICK-UP > http://67-72chevytrucks.com/vboard/s...otrash+re-hash 64 CARRYALL >http://67-72chevytrucks.com/vboard/s...=1964+suburban 66 LB >http://67-72chevytrucks.com/vboard/s...d.php?t=427852 STRENGTH/DETERMINATION/MERCILESS/FOREVER .......posted via stationary device |
|
|
|
|
09-27-2008, 09:35 PM
|
#14 |
|
1960 GMC Burb
Join Date: Jan 2008
Location: Arizona
Posts: 385
|
Re: Lower control arm ball joint question
On my 60 I drilled the original rivet out, ground it flat, used large hammer to punch them out. Then got a larger sledge hammer and got the job done.
 Good luck, it sucked for me. 
__________________
1960 GMC Suburban 1/2 ton V-6 2nd generation original owner  60 Burb Build thread: http://67-72chevytrucks.com/vboard/s...=1960+Suburban 60 to 66 Burbs only Thread: http://67-72chevytrucks.com/vboard/s...ighlight=burbs 2003 Tahoe LT 
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
