how to remove wire back up light? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

71tahoe · 01-09-2009, 03:06 PM

Seems I was right

You'll have to push the connector assy. through, cut the crimped connector and pull the spring and housing off the end. I don't know where you will find another connector to crimp on there when replacing though.
Name: backup.jpg
Views: 117
Size: 18.7 KB

Name: backup.jpg
Views: 117
Size: 18.7 KB

nac593 · 01-09-2009, 03:13 PM

Thanks for the response. I was looking and looking and just could not figure it out. It seems like there has to be a way to do it. Everything else on the truck is able to come apart, but not this? I was thinking cut it, but would really like to find a way without damaging it.

71tahoe · 01-09-2009, 03:19 PM

I didn't try this but if the rubber is still pliable, pull the spring out and try to squeeze it trough the hole. There should be some room without the spring in there.

**CPNE** · 01-09-2009, 03:35 PM

Here is the correct method.

1. Remove tailight housing from end of bed.
2. Reach in and grab the light green wire that goes to the backup housing. It should be accessible with the lower tailigh housing removed.
3. Pull it out until you can access the rubber boot that joints the housing's harness to the tailight wiring harness.
4. Separate at that boot by pulling it apart. You may find that after 40 years the rubber is hard and stiff, so you may have to really tug on it.

Dingfodgy · 01-09-2009, 03:42 PM

DO NOT CUT THE WIRE OR TERMINAL!Do what the previous poster said.
There is a weather-tight connecter right behind the taillight housing for the backup light. (Green Wire). Seperate the rubber boots and you are good to yank the B/U light housing.

chevy_mike · 01-09-2009, 04:00 PM

Quote:

Originally Posted by Dingfodgy

DO NOT CUT THE WIRE OR TERMINAL!Do what the previous poster said.
There is a weather-tight connecter right behind the taillight housing for the backup light. (Green Wire). Seperate the rubber boots and you are good to yank the B/U light housing.

Don't I know it...

Could not figure out how it came apart. Cut the wire, pulled it out and was like Doh! Pulled the connector apart on the other side.

nac593 · 01-09-2009, 04:04 PM

Hey, someone else in san diego. Where abouts are you? Do you know of any good shops or places around that relate to our trucks?

01-09-2009, 03:06 PM	#1
71tahoe Registered User Join Date: May 2006 Location: Jonesboro, AR Posts: 916	Re: how to remove wire back up light? Seems I was right You'll have to push the connector assy. through, cut the crimped connector and pull the spring and housing off the end. I don't know where you will find another connector to crimp on there when replacing though.

01-09-2009, 03:13 PM	#2
nac593 Registered User Join Date: Sep 2007 Location: san diego,ca Posts: 125	Re: how to remove wire back up light? Thanks for the response. I was looking and looking and just could not figure it out. It seems like there has to be a way to do it. Everything else on the truck is able to come apart, but not this? I was thinking cut it, but would really like to find a way without damaging it.

01-09-2009, 03:19 PM	#3
71tahoe Registered User Join Date: May 2006 Location: Jonesboro, AR Posts: 916	Re: how to remove wire back up light? I didn't try this but if the rubber is still pliable, pull the spring out and try to squeeze it trough the hole. There should be some room without the spring in there.

01-09-2009, 03:35 PM	#4
CPNE Resident Curmudgeon Join Date: Dec 1999 Location: NH Posts: 6,662	Re: how to remove wire back up light? Here is the correct method. 1. Remove tailight housing from end of bed. 2. Reach in and grab the light green wire that goes to the backup housing. It should be accessible with the lower tailigh housing removed. 3. Pull it out until you can access the rubber boot that joints the housing's harness to the tailight wiring harness. 4. Separate at that boot by pulling it apart. You may find that after 40 years the rubber is hard and stiff, so you may have to really tug on it. __________________ Currently on or near the homestead: 67 Chevy SWB 2WD stepside 350/3 on tree (Pat's) 67 GMC SWB 2WD Fleet 402/auto (Brian's under construction) 67 Chevy 3/4 ton 2WD 402/auto (Business Hauler) 67 Chevy 1 ton dually 2WD 396/4 speed (Former business hauler, Needs TLC) 68 Chevy 1/2 ton Suburban 2WD 250 six/3 on tree (Brian's Needs TLC) 70 Chevy 3/4 ton 4WD 350/4 speed (Pat's - Disguised as a 68 GMC) 71 Chevy SWB stepside (Crushed by tree - parts donor) 72 Chevy 3/4 ton 4WD (Parts donor) 72 Chevy 3/4 ton 4WD Suburban (Parts Donor) 72 GMC 3/4 ton 4WD 292 six/4 speed (Mine - Disguised as a 67 GMC) 81 GMC 4WD Dually Dump Body 350/4 speed (Business Hauler) 82 Camaro Z/28 355/Super T-10 (Pat's toy) 93 Caprice 9C1 (Brian's Cop Car) 02 Toyota Camry (Reliable but a souless steel and plastic hulk) 2011 2SS RS Camaro M6 Factory Hurst Shifter Maybe I need to sell some of this crap Yet another Bozo with a sawz-all

01-09-2009, 03:42 PM	#5
Dingfodgy Lemme show you something!! Join Date: Apr 2007 Location: St.Helens, OR. Posts: 876	Re: how to remove wire back up light? DO NOT CUT THE WIRE OR TERMINAL!Do what the previous poster said. There is a weather-tight connecter right behind the taillight housing for the backup light. (Green Wire). Seperate the rubber boots and you are good to yank the B/U light housing. __________________ '67 CST-10 LWB ("Crusty") SOLD '67 GMC SWB ("Murdock") 2000 K1500 Suburban ("Betty") '95 BMW 325i ("Joy")

01-09-2009, 04:04 PM	#7
nac593 Registered User Join Date: Sep 2007 Location: san diego,ca Posts: 125	Re: how to remove wire back up light? Hey, someone else in san diego. Where abouts are you? Do you know of any good shops or places around that relate to our trucks?



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.