anti roll bar - The 1947 - Present Chevrolet & GMC Truck Message Board Network

a1953mdl · 02-12-2009, 12:16 AM

Now can ya'll tell me about anti-roll bars.

Is there a way to build one DIY??
Maybe use a torsion bar from some other vehicle and is there a reason to use a particular length arm, etc.
At what HP or ET is one really needed?
My drag racing experience is from 25-30 years ago. This is new technology for me.

djracer · 02-12-2009, 05:03 PM

check out this one. Its pretty cheap on Ebay. Look a little over half way down the page.

http://www.67-72chevytrucks.com/vboa...=210902&page=2

a1953mdl · 02-13-2009, 11:53 PM

So they don't twist at all. A solid bar is used?
Cheap enough.
Thanks
Lee

djracer · 02-14-2009, 04:58 PM

The arms that extend out do move up and down. His looks solid but I'm sure its not.

a1953mdl · 02-14-2009, 06:07 PM

I am understanding now.
Thanks

02-12-2009, 12:16 AM	#1
a1953mdl Rusty but Trusty Join Date: Jan 2007 Location: Texas Posts: 228	anti roll bar Now can ya'll tell me about anti-roll bars. Is there a way to build one DIY?? Maybe use a torsion bar from some other vehicle and is there a reason to use a particular length arm, etc. At what HP or ET is one really needed? My drag racing experience is from 25-30 years ago. This is new technology for me. __________________ 72 SWB, 454 / th400... hoping the kids don't get all the parts before it gets built

02-12-2009, 05:03 PM	#2
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	Re: anti roll bar check out this one. Its pretty cheap on Ebay. Look a little over half way down the page. http://www.67-72chevytrucks.com/vboa...=210902&page=2 __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

02-13-2009, 11:53 PM	#3
a1953mdl Rusty but Trusty Join Date: Jan 2007 Location: Texas Posts: 228	Re: anti roll bar So they don't twist at all. A solid bar is used? Cheap enough. Thanks Lee __________________ 72 SWB, 454 / th400... hoping the kids don't get all the parts before it gets built

02-14-2009, 04:58 PM	#4
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	Re: anti roll bar The arms that extend out do move up and down. His looks solid but I'm sure its not. __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

02-14-2009, 06:07 PM	#5
a1953mdl Rusty but Trusty Join Date: Jan 2007 Location: Texas Posts: 228	Re: anti roll bar I am understanding now. Thanks __________________ 72 SWB, 454 / th400... hoping the kids don't get all the parts before it gets built



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.