Need Help - The 1947 - Present Chevrolet & GMC Truck Message Board Network

RED68SWB · 02-27-2009, 11:37 PM

I just replaced my distributor, intake, and Carburetor and now my truck wont start. The entire electrical system is dead. I thought it was the battery, but it is fully charged. I dont even have lights. Is there something that I might have missed or screwed up?

Sammy · 02-27-2009, 11:44 PM

Check your plug on the firewall in the engine department. Might have knocked that plug loose or its corroded. Everything gets power thru that connection.

72blue · 02-27-2009, 11:50 PM

clean your ground term. and the block connection. Grounds can cause lots of electrical demons.

RED68SWB · 02-27-2009, 11:59 PM

just checked it and its good. I dont understand it, it aint getting any power to anything.

RED68SWB · 02-28-2009, 12:02 AM

Quote:

clean your ground term. and the block connection. Grounds can cause lots of electrical demons.

Good Call. Ill clean it up and see how it goes.

PHAT TONY · 02-28-2009, 12:04 AM

Did you possibly short-out a fusable link?

RED68SWB · 02-28-2009, 12:07 AM

where is the fuseable link at? I checked the fuses under the dash but they are all good to go. Im a good wrench turner, but my electrician degree is still in the mail.

**El Jay** · 02-28-2009, 12:07 AM

Quote:

Originally Posted by PHAT TONY

Did you possibly short-out a fusable link?

Beat me to it.
The fusible link can be blown, but look like it's blown.

**El Jay** · 02-28-2009, 12:27 AM

I've seen them in 2 locations on GM trucks.

The 1st is a 16 Ga. (but with the heavier insulation, it looks like a 12 Ga. wire) wire from the battery to a junction block on the fender well near the battery.
The 2nd location is off the battery cable terminal on the starter solenoid. It too looks like a 12 Ga. wire.

If worse comes to worse, you can chase the wire backwards from the bulkhead connector for your fuse block.

Make sure everything is clean & shiny; battery posts, cable terminals at both ends, ground at the block, on & on & on.

A friend of mine had a similar problem. It was some corrosion in the bulkhead connector for the fuse block.
I had a problem that took me over a week to track down, & at that, I found it accidentally. The ground cable to the engine block was corroded inside the terminal at the block.

Good luck!
I hate electrical problems!

PHAT TONY · 02-28-2009, 12:28 AM

It's gonna be a softer section of wire, some kinda connector at each end, usually in the alt positive line or a starter line. It's a light inner heavy gage lookin and if burnt, it'll feel hallow inside. They're usually 3-4/5 inches long. Sorry to repeat, we're posting in unison.

Andy4639 · 02-28-2009, 12:39 AM

Check the + wire coming off the Battery to the fender at the block mounted on passenger fender make sure all the wires are intact. Then follow the wires across the radiator support. You will find the small fuses here.

RED68SWB · 02-28-2009, 12:41 AM

Thanks for the help. I guess I got my day planned out for tomorrow. Hahaha, man I hope i get this figured out.

**El Jay** · 02-28-2009, 01:53 AM

Quote:

Originally Posted by PHAT TONY

It's gonna be a softer section of wire, some kinda connector at each end, usually in the alt positive line or a starter line. It's a light inner heavy gage lookin and if burnt, it'll feel hallow inside. They're usually 3-4/5 inches long. Sorry to repeat, we're posting in unison.

We're all working together to help each other.

02-27-2009, 11:37 PM	#1
RED68SWB Registered User Join Date: Feb 2009 Location: Copperas Cove, TX Posts: 8	Need Help I just replaced my distributor, intake, and Carburetor and now my truck wont start. The entire electrical system is dead. I thought it was the battery, but it is fully charged. I dont even have lights. Is there something that I might have missed or screwed up?

02-27-2009, 11:44 PM	#2
Sammy Registered User Join Date: Apr 2000 Location: Bonne Terre, Mo Posts: 3,005	Re: Need Help Check your plug on the firewall in the engine department. Might have knocked that plug loose or its corroded. Everything gets power thru that connection. __________________ '69 Chevy Long Fleet & '71 GMC Short Step & Project "ODD BALL" "You can wash a pig, soak it in most expensive perfume. In the end it is still just a pig." ODD BALL build thread http://67-72chevytrucks.com/vboard/s...d.php?t=478629"

02-27-2009, 11:50 PM	#3
72blue Registered User Join Date: Feb 2009 Location: arroyo grande, ca Posts: 206	Re: Need Help clean your ground term. and the block connection. Grounds can cause lots of electrical demons.

02-27-2009, 11:59 PM	#4
RED68SWB Registered User Join Date: Feb 2009 Location: Copperas Cove, TX Posts: 8	Re: Need Help just checked it and its good. I dont understand it, it aint getting any power to anything.

02-28-2009, 12:04 AM	#6
PHAT TONY Registered User Join Date: Aug 2008 Location: Red Deer ab canada Posts: 1,250	Re: Need Help Did you possibly short-out a fusable link?

02-28-2009, 12:07 AM	#7
RED68SWB Registered User Join Date: Feb 2009 Location: Copperas Cove, TX Posts: 8	Re: Need Help where is the fuseable link at? I checked the fuses under the dash but they are all good to go. Im a good wrench turner, but my electrician degree is still in the mail.

02-28-2009, 12:27 AM	#9
El Jay Gone to greener pastures Join Date: May 2007 Location: Gateway to the Delta Posts: 7,354	Re: Need Help I've seen them in 2 locations on GM trucks. The 1st is a 16 Ga. (but with the heavier insulation, it looks like a 12 Ga. wire) wire from the battery to a junction block on the fender well near the battery. The 2nd location is off the battery cable terminal on the starter solenoid. It too looks like a 12 Ga. wire. If worse comes to worse, you can chase the wire backwards from the bulkhead connector for your fuse block. Make sure everything is clean & shiny; battery posts, cable terminals at both ends, ground at the block, on & on & on. A friend of mine had a similar problem. It was some corrosion in the bulkhead connector for the fuse block. I had a problem that took me over a week to track down, & at that, I found it accidentally. The ground cable to the engine block was corroded inside the terminal at the block. Good luck! I hate electrical problems! __________________ '69 Chevy 1/2 T LWB Stepper: Daily Beater '72 GMC 3/4 T Fleet: Another Daily Beater '72 Plymouth Gran Coupe: ? "Ah women. They make the highs higher and the lows more frequent." Friedrich Nietzsche "Never kick a fresh turd on a hot day." Harry S. Truman GUN CONTROL: Never having to say, "I missed you." Always fire two warning shots into your attacker's chest area before putting a bullet between his eyes. Paraphrased from Louis Awerbuck

02-28-2009, 12:28 AM	#10
PHAT TONY Registered User Join Date: Aug 2008 Location: Red Deer ab canada Posts: 1,250	Re: Need Help It's gonna be a softer section of wire, some kinda connector at each end, usually in the alt positive line or a starter line. It's a light inner heavy gage lookin and if burnt, it'll feel hallow inside. They're usually 3-4/5 inches long. Sorry to repeat, we're posting in unison. Last edited by PHAT TONY; 02-28-2009 at 12:31 AM. Reason: Don't want to double post.

02-28-2009, 12:39 AM	#11
Andy4639 Old member Join Date: Jan 2002 Location: Liberty, & Garden City S.C. , U.S. Posts: 19,936	Re: Need Help Check the + wire coming off the Battery to the fender at the block mounted on passenger fender make sure all the wires are intact. Then follow the wires across the radiator support. You will find the small fuses here. __________________ 1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs.

02-28-2009, 12:41 AM	#12
RED68SWB Registered User Join Date: Feb 2009 Location: Copperas Cove, TX Posts: 8	Re: Need Help Thanks for the help. I guess I got my day planned out for tomorrow. Hahaha, man I hope i get this figured out.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.