|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
03-11-2009, 09:58 PM
|
#26 |
|
Modern day Fred Sanford
Join Date: Oct 2005
Location: Greeneville,TN
Posts: 330
|
Re: 1-tonmudders 241/205 Doubler
Ok so after a short hiatus I finally got back on this today.Pulled the old 400/205 out.
  Since I went to a 241 case it requires a different lenth output shaft in the 400.Their are 3 different lenth's on the 400 output's and it depends on what case your runnin.They are as follows. NP203 NP205-figure eight or racetrack pattern with the short input NP-205,208,241-round pattern with the long input. Since I had to change the output shaft and the 400 I was running had a ear broke off of it I elected to just completely replace the trans.I had a good lo-mileage 400 from a CUCV that originally had a 208 behind it so the 241 will be a direct bolt in.  Got the trans in and all buttoned up and started assmebling the 241.   Not a lot of progress for 8 hours work but considering all the distractions I done pretty good. I also got these in last week.   
|
|
|
|
03-12-2009, 10:08 AM
|
#27 |
|
Registered User
Join Date: Feb 2000
Location: Modesto, CA
Posts: 1,842
|
Re: 1-tonmudders 241/205 Doubler
Oooooooooo
  Nice! 
__________________
1972 K5 MPFI454/Sm465/Np205/D60/14FFd/Re-Centerd H1s w/Swamper Iroks
|
|
|
|
|
03-12-2009, 10:37 AM
|
#28 |
|
Registered User
 
Join Date: Feb 2007
Location: Star Valley, WY
Posts: 2,038
|
Re: 1-tonmudders 241/205 Doubler
hey that looks pretty sharp! who's twin stick assembly is that?
__________________
Steve 1971 GMC Longbox. Full Roller Stroker 489 w/ FiTech EFI, Chris Straub Cam/NV4500/205/D60/14B w. Grizzly Locker and 4.11's. 2" Lift on 33's |
|
|
|
|
03-12-2009, 11:33 AM
|
#29 |
|
Registered User
Join Date: Oct 2006
Location: Southern Kalifornia
Posts: 3,066
|
Re: 1-tonmudders 241/205 Doubler
Very nice. Good work.
-Lance
__________________
------------------------------------------------------ -Lance 2000 Chevy C2500, 5.7, 4L80e 1999 Suburban K2500, 7.4, 4L80e 1980 Camaro..son's car...PROJECT |
|
|
|
|
03-13-2009, 08:15 AM
|
#30 |
|
Modern day Fred Sanford
Join Date: Oct 2005
Location: Greeneville,TN
Posts: 330
|
Re: 1-tonmudders 241/205 Doubler
The stick's are from JB fab.
http://www.jbfab.net/Merchant2/merchant.mv? |
|
|
|
|
03-13-2009, 09:25 AM
|
#31 |
|
Special Order
  
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,851
|
Re: 1-tonmudders 241/205 Doubler
It must be 241-only.There`s been 208-only kits for awhile.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
