|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
05-04-2009, 11:56 AM
|
#1 |
|
Registered User
Join Date: Jan 2009
Location: seffner, fl
Posts: 9
|
Need power window help
I got this 85 k10 about 4 months ago. The passenger side window moved up
and down very slow. When I replaced old window seal 2 months ago with new one it would'nt move at all w/o help. I "assumed" the motor was just worn out. This weekend I replaced the motor and it made no difference. The rails don't look bent or anything damaged. Any suggestions will be appreciated. Seagator 1985 K10 S/B Diesel |
|
|
|
05-04-2009, 04:53 PM
|
#2 |
|
www.73-87chevytrucks.com
 
Join Date: Dec 1999
Location: Birmingham, AL
Posts: 6,935
|
Re: Need power window help
Where did the motor come from?
Did you lube the guide channels?
__________________
Chris Lucas 1973 Chevy C-10 1978 GMC Jimmy (2WD) - SOLD 1987 R10 twin turbo LS 1991 R3500 SRW CrewCab 1985 K5 diesel swapped project 1989 K5 2WD conversion w/ Vette susp Project Captkaos Customs 73-87chevytrucks.com |
|
|
|
|
05-04-2009, 05:01 PM
|
#3 |
|
Registered User
Join Date: Jan 2009
Location: seffner, fl
Posts: 9
|
Re: Need power window help
AutoZone and sprayed rail with white lithium grease.
|
|
|
|
|
05-05-2009, 05:31 PM
|
#4 |
|
Registered User
Join Date: Feb 2008
Location: blanchard, ok
Posts: 30
|
Re: Need power window help
That's funny, I have the same problem only my window stops halfway and i have to pull it the rest of the way up.
|
|
|
|
|
05-05-2009, 05:34 PM
|
#5 |
|
6.0 powered square
Join Date: Feb 2008
Location: Mesquite texas
Posts: 3,459
|
Re: Need power window help
I would also check your grounds and connections
__________________
Aaron 1980 c-10 short bed lowered, cammed 6.0, 4l80e 3600 stall, smp tune, wilwoods, and flames best time so far best et 7.86 @87 on motor 7.57 90 on a 75 shot Build http://67-72chevytrucks.com/vboard/s...d.php?t=283326 |
|
|
|
|
05-05-2009, 05:45 PM
|
#6 |
|
Registered User
Join Date: Feb 2009
Location: Oklahoma
Posts: 7,461
|
Re: Need power window help
You may call Autozone. It's not unheard of to get a bad motor even though it's new. A lot of those are remanufactured.
|
|
|
|
|
05-05-2009, 05:53 PM
|
#7 |
|
Registered User
Join Date: Sep 2003
Location: The Netherlands
Posts: 994
|
Re: Need power window help
Either check for voltage at the connector or get a spare battery and hook it straight to the motor. If the window flies up and down you ahve a bad connection and need to sort it out to get full 12~13V to the motor.
Last edited by TwinTurbo; 07-13-2009 at 10:38 AM. |
|
|
|
|
05-06-2009, 02:03 PM
|
#8 |
|
Registered User
Join Date: Mar 2008
Location: Lockport, NY
Posts: 106
|
Re: Need power window help
i would check how much voltage you are getting at the motor you might have a voltage dorp problem so your motor isint getting it required power to run at optimal speed
|
|
|
|
|
05-06-2009, 06:28 PM
|
#9 |
|
Registered User
 
Join Date: May 2005
Location: Tallahassee Fl
Posts: 773
|
Re: Need power window help
120 AMP alternator will not fix it......
125.00 New motors/regulators 18.00 Junkyard window 30.00 New Switches 50.00 Window Felt kit 100.00 Alternator. My Dad was a GM tech back in the day, says powdered graphite the new felts lightly. He said that GM had a "felt lube" powder years ago, but it cannot be found. If that doesn't work, rewiring with relays. |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
