02 noise - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jackyl9999 · 07-19-2009, 08:52 AM

I have started to notice a noise in the front end of my 2002 z71. It does it the most when I make a slight turn to the left (like on a curve in a street). I got under the truck and looked around did not see anything rubbing. The sound is hard to describe but sounds metallic, its not a constant but kind of like in waves.

Maybe half-shaft?

Any ideas?

**truckdude239** · 07-19-2009, 09:30 AM

Sounds likeba wheel bearingbto me

**Boog** · 07-19-2009, 09:38 AM

How bout the disk brake pads? They have a wear indicator (schreecher for lack of a better description) that will touch the rotor when they get worn down close. At the early signs of wear they might only schreech when in a turn.

jackyl9999 · 07-19-2009, 09:43 AM

Anyway to check out the hub assembly?

Hope its brake pads though.

**Boog** · 07-19-2009, 09:54 AM

Put a jack under the control arm and raise the wheel off the ground then with one hand on the tire at 12 and one hand at 6 try rocking the wheel up and down. There shouldn't be any noticeable slack in it. Spin the wheel while up off the ground and see if it makes any noise that way. Pull the wheel off and inspect the brake pads. The schreecher is located on the bottom edge of the outside brake pad. It is probably very close to touching the rotor.

jackyl9999 · 07-19-2009, 10:42 AM

Alright I'll check it out.

Thanks fellow arkansan

**truckdude239** · 07-19-2009, 01:52 PM

could be brakes pads all i know is my 1991 escort make a metal grinding sound ever time i maded a right turn (curve) and it turned out to be the left front wheel bearing was bad had no play in it but i replaced the bearing and it went away

jackyl9999 · 07-19-2009, 08:13 PM

I checked it out. Looks like its the bearing. Its sitting at the dealership. So much for truck parts for my project!

Thanks for the replies guys.

Steve

07-19-2009, 08:52 AM	#1
jackyl9999 Registered User Join Date: Feb 2003 Location: Paragould, Ar Posts: 571	02 noise I have started to notice a noise in the front end of my 2002 z71. It does it the most when I make a slight turn to the left (like on a curve in a street). I got under the truck and looked around did not see anything rubbing. The sound is hard to describe but sounds metallic, its not a constant but kind of like in waves. Maybe half-shaft? Any ideas? __________________ 1970 Gmc Grande Sierra Swb 2wd LSX (LQ4/4L80e) 1990 K1500 Daily

07-19-2009, 09:30 AM	#2
truckdude239 Senior Member Join Date: Sep 2005 Location: Lewisville, Nc Posts: 10,238	Re: 02 noise Sounds likeba wheel bearingbto me __________________ David fuller Ase Certified Mechanic Click here to help support our board!! 1971 Chevy c-10 under going a 4.8l LSx swap Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=421305 2007 Honda Accord my daily 145kmiles 2002 Honda Accord 4 door With 330k(sisters car) 2005 toyota Avalon 228k( brothers car) 2002 Sububran 5.3 245k 2000 Tahoe 5.3l 378 General manager for Marco's Carwash & lube

07-19-2009, 09:38 AM	#3
Boog laying low Join Date: Mar 2001 Location: Searcy, Ark. USA Posts: 13,534	Re: 02 noise How bout the disk brake pads? They have a wear indicator (schreecher for lack of a better description) that will touch the rotor when they get worn down close. At the early signs of wear they might only schreech when in a turn. __________________ Boog 69 Chevy stepside, 358/T350, 4.11 posi, 4.5/4 drop, rallys, poboy driver primer is finer 91 Chevy sportside, Tahoe, Yukon & GMC Crewcab All GM..'nuff said. I stand for the flag and kneel at the cross

07-19-2009, 09:43 AM	#4
jackyl9999 Registered User Join Date: Feb 2003 Location: Paragould, Ar Posts: 571	Re: 02 noise Anyway to check out the hub assembly? Hope its brake pads though. __________________ 1970 Gmc Grande Sierra Swb 2wd LSX (LQ4/4L80e) 1990 K1500 Daily

07-19-2009, 09:54 AM	#5
Boog laying low Join Date: Mar 2001 Location: Searcy, Ark. USA Posts: 13,534	Re: 02 noise Put a jack under the control arm and raise the wheel off the ground then with one hand on the tire at 12 and one hand at 6 try rocking the wheel up and down. There shouldn't be any noticeable slack in it. Spin the wheel while up off the ground and see if it makes any noise that way. Pull the wheel off and inspect the brake pads. The schreecher is located on the bottom edge of the outside brake pad. It is probably very close to touching the rotor. __________________ Boog 69 Chevy stepside, 358/T350, 4.11 posi, 4.5/4 drop, rallys, poboy driver primer is finer 91 Chevy sportside, Tahoe, Yukon & GMC Crewcab All GM..'nuff said. I stand for the flag and kneel at the cross

07-19-2009, 10:42 AM	#6
jackyl9999 Registered User Join Date: Feb 2003 Location: Paragould, Ar Posts: 571	Re: 02 noise Alright I'll check it out. Thanks fellow arkansan __________________ 1970 Gmc Grande Sierra Swb 2wd LSX (LQ4/4L80e) 1990 K1500 Daily

07-19-2009, 01:52 PM	#7
truckdude239 Senior Member Join Date: Sep 2005 Location: Lewisville, Nc Posts: 10,238	Re: 02 noise could be brakes pads all i know is my 1991 escort make a metal grinding sound ever time i maded a right turn (curve) and it turned out to be the left front wheel bearing was bad had no play in it but i replaced the bearing and it went away __________________ David fuller Ase Certified Mechanic Click here to help support our board!! 1971 Chevy c-10 under going a 4.8l LSx swap Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=421305 2007 Honda Accord my daily 145kmiles 2002 Honda Accord 4 door With 330k(sisters car) 2005 toyota Avalon 228k( brothers car) 2002 Sububran 5.3 245k 2000 Tahoe 5.3l 378 General manager for Marco's Carwash & lube

07-19-2009, 08:13 PM	#8
jackyl9999 Registered User Join Date: Feb 2003 Location: Paragould, Ar Posts: 571	Re: 02 noise I checked it out. Looks like its the bearing. Its sitting at the dealership. So much for truck parts for my project! Thanks for the replies guys. Steve __________________ 1970 Gmc Grande Sierra Swb 2wd LSX (LQ4/4L80e) 1990 K1500 Daily



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.