how much should i tighten my new cab mounts? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Dropt72Shortbed · 04-01-2003, 07:10 PM

phew... just gave myself a hernia getting the new cab all lined up on the frame. i got all the cab mount bolts in just need to tighten them up a bit more, how tight should i go?

now its time to get the doors on, then core support, then gas tank, wiring harness, then steering column and i can move her in the garage to start bagging her. its so nice having spring break to work on my truck!!!

**1971Stepside** · 04-01-2003, 07:13 PM

Blake, I wouldn't tighten them until you have the front clip all lined up and adjusted to wher you want it.

Dropt72Shortbed · 04-01-2003, 07:19 PM

Quote:

Originally posted by 1971Stepside
Blake, I wouldn't tighten them until you have the front clip all lined up and adjusted to wher you want it.

good point!

i dont think theres that much play in them though? i figured most of the adjustment would be in the actual front clip. anyways ill take your word for it since im sure you guys have done this a few times before, theres also no reason to have it completely snug at the moment.

cdowns · 04-01-2003, 07:47 PM

30foot/pounds

Dreaminator · 04-01-2003, 10:00 PM

tighten them enough to keep the the cab square. Tighten everything after front clip is mounted. I tightened mine a little more than cdowns recommended but I also did a lot of repair with all new cab mounts. Sure is quieter with double insolation and all the holes fixed!

KEH · 04-01-2003, 10:09 PM

Dreaminator,

Just curious what you used for insulation?

Gordo · 04-01-2003, 10:13 PM

Like what has allready been posted, leave them loose until the nose and FRONT BUMPER has been installed. If the cab is off a 1/4" by the time you get to the bumper the front of the nose is 1" off center.

Dreaminator · 04-02-2003, 07:34 PM

I bought a "double insolation" kit from LMC. I also put down the heaviest weight carpet I could buy from the kits available at Summit. Finally, after we removed the gas tank I also ran carpet up to just below the window. The engine rumbles, but I ran 2 1/2 all the way back to the bumpers as my friend's truck with flowmaster 40s was just on the edge of being too loud. I think insolation is one place a lot of guys cut corners. All it takes is some cardboard for templates and a little spray glue.

KEH · 04-02-2003, 08:47 PM

Thanks for the info, and good point.

04-01-2003, 07:10 PM	#1
Dropt72Shortbed Registered User Join Date: May 2002 Location: Huntington Beach CA Posts: 678	how much should i tighten my new cab mounts? phew... just gave myself a hernia getting the new cab all lined up on the frame. i got all the cab mount bolts in just need to tighten them up a bit more, how tight should i go? now its time to get the doors on, then core support, then gas tank, wiring harness, then steering column and i can move her in the garage to start bagging her. its so nice having spring break to work on my truck!!!

04-01-2003, 07:13 PM	#2
1971Stepside Almost Satisfied Join Date: Mar 2002 Location: Springfield, MO Posts: 2,932	Blake, I wouldn't tighten them until you have the front clip all lined up and adjusted to wher you want it. __________________ 1971 C10 Stepside. LSx 6.0 with BTR Stage IV, Speed Engineering Headers, 4L80e transmission w/3200 Circle-D Stall. 3.73. Posi. Purchased this truck when I was 17. I started the rebuild (or take apart) in 1993. I have drug it around all over the country in pieces. Finally back on the road in 2021. "I can't complain, but sometimes I still do. Life's been good to me so far."

04-01-2003, 07:47 PM	#4
cdowns Senior Member Join Date: Jan 2003 Location: daytonabeach Posts: 22,956	30foot/pounds __________________ 71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY

04-01-2003, 10:00 PM	#5
Dreaminator Dreaminator Join Date: Feb 2003 Location: Broken Arrow, Oklahoma Posts: 156	tighten them enough to keep the the cab square. Tighten everything after front clip is mounted. I tightened mine a little more than cdowns recommended but I also did a lot of repair with all new cab mounts. Sure is quieter with double insolation and all the holes fixed! __________________ The Dreaminator Daily Driver 1971 Cheyenne 10 Lwb Tilt/Tac 402 .030 TH400.

04-01-2003, 10:09 PM	#6
KEH Better late than never Join Date: Dec 2001 Location: Columbus, IN Posts: 324	Dreaminator, Just curious what you used for insulation? __________________ 1970 C/10 SWB Stepside

04-01-2003, 10:13 PM	#7
Gordo Registered User Join Date: Jan 2001 Location: Killingworth, CT. USA Posts: 3,378	Like what has allready been posted, leave them loose until the nose and FRONT BUMPER has been installed. If the cab is off a 1/4" by the time you get to the bumper the front of the nose is 1" off center. __________________ 1971 C10 swb stepside 350/700R4/3.73posi (retired as of 4/22/03) 1998 S10 short bed 2002 S10 Blazer 1942 Oldsmobile 1958 Massey Harris Pony 1951 Wife Killingworth, Connecticut May those who love us, love us, any of those who do not love us, may God turn their hearts. And if God is unable to turn their hearts, may he turn their ankles so we may know them by their limping. A man who works with his hands is a laborer; a man who works with his hands and his brain is a craftsman; but a man who works with his hands and his brain and his heart is an artist.

04-02-2003, 07:34 PM	#8
Dreaminator Dreaminator Join Date: Feb 2003 Location: Broken Arrow, Oklahoma Posts: 156	I bought a "double insolation" kit from LMC. I also put down the heaviest weight carpet I could buy from the kits available at Summit. Finally, after we removed the gas tank I also ran carpet up to just below the window. The engine rumbles, but I ran 2 1/2 all the way back to the bumpers as my friend's truck with flowmaster 40s was just on the edge of being too loud. I think insolation is one place a lot of guys cut corners. All it takes is some cardboard for templates and a little spray glue. __________________ The Dreaminator Daily Driver 1971 Cheyenne 10 Lwb Tilt/Tac 402 .030 TH400.

04-02-2003, 08:47 PM	#9
KEH Better late than never Join Date: Dec 2001 Location: Columbus, IN Posts: 324	Thanks for the info, and good point. __________________ 1970 C/10 SWB Stepside



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.