I think i have it all???? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

BADPURPLE70CHEVY · 09-10-2009, 07:02 PM

Going to start on my disk brake swap on my 70 chevy in about a week. Heres what i have in parts. Please tell me what im missing if any. FRONT- 72SPINDLES,ROTORS,ALL BEARINGS,72 CENTERLINK WITH ALL INNER AND OUTER TIE RODS ATTACHED(ONLY NEED OUTER ),NEW PADS,NEW 72 CALIPERS,72 PROP VALVE,NEW 72 MASTER CYLINDER. REAR- AXLES OUT OF 71,NEW DRUMS,NEW SHOES.... I MAY HAVE MORE AND FORGOT SOMETHING... DID I FORGET ANYTHING??????

CSGAS · 09-10-2009, 08:19 PM

Hoses and I think you'll be happier with a pair of 72 upper ball joints for those spindles--not sure on the last part.

Tx Firefighter · 09-10-2009, 08:42 PM

Upper and lower ball joints

Brake rotor dust shields, rubber gaskets, and 5/16 bolts that secure them to the caliper.

Brake hoses and lines.

Castle nut and special washer for wheel bearings.

Dust caps

Banjo bolts

Axle seals for the rear end

Lube for rear end

Silicone or gasket for differential cover.

Brake fluid

oldblue1968chevy · 09-10-2009, 10:01 PM

a good weekend

oh a pickle fork and a big sledge(go to store, find biggest one you think you can handle, then go 3 sizes bigger lol) its dang near impossible to separate tierod ends/balljoints

other than that you've just about got it covered

Jim_PA · 09-10-2009, 10:13 PM

I wish I would have done a 73-87 front suspension. You'll find the ball joints for a 71-72 will cost you about $50 each. 73-87 stuff is half the cost.

Well, at least I'll get to do it again in a few years on my next project.

Legolas894 · 09-10-2009, 10:51 PM

All good stuff here.
-Spring kit (if doing rear shoes), brake cleaner, spring removal tool (s).

-Wheel cylinders if you have leaks.
-Bearing grease to repack bearings.
-Seal removal tool.

Lot's of time!

Those special brake lines wrenches would be nice if you don't have them.

unclewatts · 09-11-2009, 04:16 AM

Dictionary of American Slang for new swear words to use while you're working.

a Miller draft?

09-10-2009, 07:02 PM	#1
BADPURPLE70CHEVY 406 Powered Join Date: Aug 2009 Location: waynesville,n.c. Posts: 877	I think i have it all???? Going to start on my disk brake swap on my 70 chevy in about a week. Heres what i have in parts. Please tell me what im missing if any. FRONT- 72SPINDLES,ROTORS,ALL BEARINGS,72 CENTERLINK WITH ALL INNER AND OUTER TIE RODS ATTACHED(ONLY NEED OUTER ),NEW PADS,NEW 72 CALIPERS,72 PROP VALVE,NEW 72 MASTER CYLINDER. REAR- AXLES OUT OF 71,NEW DRUMS,NEW SHOES.... I MAY HAVE MORE AND FORGOT SOMETHING... DID I FORGET ANYTHING?????? __________________ 70 GMC 68 c10 2002 silverado 72 4x4

09-10-2009, 08:19 PM	#2
CSGAS optomistic ah-so Join Date: Mar 2009 Location: Charlotte, NC Posts: 544	Re: I think i have it all???? Hoses and I think you'll be happier with a pair of 72 upper ball joints for those spindles--not sure on the last part. __________________ Rubbing is Racin' Ribbing is Bench Racin' 1970 C-10 lwb Fleetside. Originally 350 2-bbl 3-on-the-tree, m/b, m/w, m/s no a/c. Currently running on a '76 Camaro 305.

09-10-2009, 08:42 PM	#3
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Re: I think i have it all???? Upper and lower ball joints Brake rotor dust shields, rubber gaskets, and 5/16 bolts that secure them to the caliper. Brake hoses and lines. Castle nut and special washer for wheel bearings. Dust caps Banjo bolts Axle seals for the rear end Lube for rear end Silicone or gasket for differential cover. Brake fluid __________________ I'm on the Instagram- @Gearhead_Kevin

09-10-2009, 10:01 PM	#4
oldblue1968chevy Grandpa in the rustmobile... Join Date: Nov 2008 Location: Spokane WA/Viola TN Posts: 11,422	Re: I think i have it all???? a good weekend oh a pickle fork and a big sledge(go to store, find biggest one you think you can handle, then go 3 sizes bigger lol) its dang near impossible to separate tierod ends/balljoints other than that you've just about got it covered __________________ John Goose-1968 C10 355,9.32-1CR, Vortec Heads ,262 voodoo, 3.73:1 3OTT (HS ride/beater/farm truck) http://67-72chevytrucks.com/vboard/s...d.php?t=317684 Grams 53-1953 Chevrolet Belair http://67-72chevytrucks.com/vboard/s...=1#post4327784 1969 Chevy C10 Shortbed 4.5/6?" Frame off resto http://67-72chevytrucks.com/vboard/s...d.php?t=548136 1999 Toyota Tacoma 4x4

09-10-2009, 10:13 PM	#5
Jim_PA Registered User Join Date: May 2005 Location: PA Posts: 2,696	Re: I think i have it all???? I wish I would have done a 73-87 front suspension. You'll find the ball joints for a 71-72 will cost you about $50 each. 73-87 stuff is half the cost. Well, at least I'll get to do it again in a few years on my next project. Last edited by Jim_PA; 09-10-2009 at 10:14 PM.

09-10-2009, 10:51 PM	#6
Legolas894 Chemist under the hood... Join Date: Apr 2009 Location: Fort Erie,ON, Canada Posts: 617	Re: I think i have it all???? All good stuff here. -Spring kit (if doing rear shoes), brake cleaner, spring removal tool (s). -Wheel cylinders if you have leaks. -Bearing grease to repack bearings. -Seal removal tool. Lot's of time! Those special brake lines wrenches would be nice if you don't have them. __________________ Current fleet: 2013 GMC Sierra, 5.3L, 4x4 1988 GMC Sierra, 305, Auto 1984 Jeep Grand Wagoneer, 360 V8 1997 VW Cabrio, 2.0L 2017 Toyota Rav4, 2.5L Stuff I wish I still had: 2013 Toyota Matrix [RIP] 1967 GMC 910 Fleetside, 283 V8 [1st Love-SOLD] 1987 Jeep Cherokee Laredo 4X4, 4.0 I-6 [SOLD} 1994 Chevrolet Caprice Classic, 5.7LV8 [SOLD] 1995 Chevrolet Astro AWD, 4.3L V6 (RIP) 1998 Chevrolet Suburban 4x4, 5.7L V8 [SOLD]

09-11-2009, 04:16 AM	#7
unclewatts 70 Chevrolet=Obsession Join Date: Jun 2009 Location: nice ca Posts: 1,067	Re: I think i have it all???? Dictionary of American Slang for new swear words to use while you're working. a Miller draft? __________________ I'm Just like my truck. Old, Ugly and Grouchy. Except my truck starts easily in the morning and doesn't smoke! IT'S NOT EASY BEING GREEN! -Kermit the frog 1970 Chevrolet C-10 Longbed Stepside : 350, Muncie M20, 3.08 GM corp. positraction Forest green exterior/light green interior(Where all my money goes) 1996 Toyota Corolla (Parts runner)



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.