anyone running 3x2, 6 pack

[BCOWANWHEELS]

I'am building a long rod 400sbc for my truck now, heres the spec's.
.040 over block
400 crank
5.7 rods
11 to 1 compression
dart aluminum heads, big valves
hei dist.
balanced-clearenced
3 rochester 2bbls on edelbrock aluminum manifod (all polished )
mild cam ( just enough to sound good and not kill bottom end torque 3.73 gears (275/60r15 rear tires )
400 turbo with g/v o.d. unit & very mild stall converter
vette ram horns and 2 1/2" exhaust, x pipe, flow masters

p.s.
i can post pic,s. of my 3x2bbl setup if you need to see it for something. i had CHARLIE PRICE IN FLORIDA RBUILD THEM FOR ME. I "DONT " RECOMEND HIM BECAUSE IT TOOK HIM ALMOST 2 YEARS AND BOY IS HE EXPENSIVE....

[meyer4589]

thanks for the info.
I'm thinking about running the set-up on my 327 when I get around to building it, but I've been looking around at summit and jegs and their combos are like 1800 bucks. Do you know anywhere you can get parts for it at a decent price?

[BCOWANWHEELS]

http://www.vintagespeed.com/

I HAVE CLOS TO $2200.00 IN MY SETUP AND I FURNISHED THE CARB CORES (348 SETUP 3X2BBL'S )
AND I HAD MY MANIFOLD POLISHED AS YOU CAN SEE

[cdowns]

be real rreal carefull when dealing with charli price at vintage speed// over on the HAMB the rotio is like 20to 1 people who have been screwed by him// yep his stuff looks good but doesnt run worth S^^t

[BCOWANWHEELS]

i had alot of problems with him on getting mine done. i had to get a little firm with him. CDOWNS WHO DID YOUR SETUP ?

[Northern lights]

I ran one for years on my '57 2dr ht back in the 80's. Had it on a 350, 11.5:1 pistons, 525 lift cam with 305 gross dur, 264 @ .050 or there abouts. I loved it. Kept it all these years and am in the process of getting it ready to put on the 327 in my '64. Mine is a 1962-64 vintage edelbrock (they only made it those 3 years) with adaptors to accept the carbs from a 389 pontiac. here's a pic of when I dug it out of the shed and after a bit of work. It's almost ready, just a few things to finish up.

[cdowns]

Originally Posted by BCOWANWHEELS

i had alot of problems with him on getting mine done. i had to get a little firm with him. CDOWNS WHO DID YOUR SETUP ?

i got mine from him also so i speak from experience//i had to purchase all new needles and power valves as well as getting the carbs stripped and recoated before that system would run properly

[Northern lights]

Originally Posted by BCOWANWHEELS

I'am building a long rod 400sbc for my truck now, heres the spec's.
.040 over block
400 crank
5.7 rods
11 to 1 compression
dart aluminum heads, big valves
hei dist.
balanced-clearenced
3 rochester 2bbls on edelbrock aluminum manifod (all polished )
mild cam ( just enough to sound good and not kill bottom end torque 3.73 gears (275/60r15 rear tires )
400 turbo with g/v o.d. unit & very mild stall converter
vette ram horns and 2 1/2" exhaust, x pipe, flow masters

....

Are you sure about that HEI. Won't even come close to fittin' behind the rear carb on mine. I ran an Accel dual point back in the day and it just barely fit. I'm planning to put a pertronics electronic upgrade in my old Accel dist.