|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
09-21-2009, 06:23 PM
|
#1 |
|
Sb 400 club
Join Date: Nov 2005
Location: NH / MA
Posts: 2,741
|
Tansfer case spacer?? Basic question
Well lifted my 77 roughly 4-5 inch. It goes okay but I think it has some vibes. I have seen alot of people taking the inch or so spacers that are on the T case crossmeber bolts and putting them between the frame and cross member. Will this put added stress on my motor mounts??? Could this cause cracking around the holes in the frame? I am not happy about the idea of lowering the T case and loosing ground clearance but I want to get this rig going and get some wheeling in before the snow flies.
Thanks and I know it is kinda a lame question
__________________
 1984 chevy c10, built 400sb,.(SOLD )77 K10 Project / daily driver "The Grinch" http://67-72chevytrucks.com/vboard/s...d.php?t=318363 1956 Willys Wagon (327 chevy) Project (Now Buick 225) 1980 Corvette L-48 4 speed 1992 Mustang GT built 5.0 5 speed  1985 C10 LWB Sold 1982 K10 SWB plow truck Parted out 1986 D30 M1028 fire brush truck Parted out |
|
|
|
09-21-2009, 06:57 PM
|
#2 |
|
Registered User
 
Join Date: Feb 2001
Location: East Central, MO
Posts: 11,336
|
Re: Tansfer case spacer?? Basic question
I lowered mine a long time ago. Used the spacers then got some aluminum spacers made after I found out they helped. Never replaced the motor mounts and no cracks that I know of.
Last edited by Mudder; 09-21-2009 at 06:57 PM. |
|
|
|
|
09-21-2009, 07:05 PM
|
#3 |
|
Registered User
Join Date: Jun 2005
Location: Grand Junction , CO
Posts: 602
|
Re: Tansfer case spacer?? Basic question
i used 1x2 rectangle tubing. nice solid mounting surface. 1 inch of ground clearance loss at the t-case is nothing. You will never notice it. If you were going to get high centered, the 1 inch would not of made a difference either way.
__________________
71 swb 4x4, 37" Iroks, t400/205 496 77 CJ-7, Narrowed Dana 60 Lockrite, 14 Bolt Spool, 4.56 gears, 39.5" boggers. 360 t-18/d20 |
|
|
|
|
09-21-2009, 09:30 PM
|
#4 |
|
the pollock
Join Date: May 2008
Location: abilene, texas
Posts: 4,423
|
Re: Tansfer case spacer?? Basic question
it's only "bad" if you have crappy mounts....
it brings your distributor closer to the fire wall.. but my solution was replace the missing/corroded body bushings.. http://www.jackit.com/store/supercart.cgi?s=skj_tcl15
__________________
Jack of ALL trades, Master of none.. (but one... procrastination) Army vet 02-08 RIP El Jay! Miss you brother! http://67-72chevytrucks.com/vboard/s...d.php?t=343538 http://67-72chevytrucks.com/vboard/s...d.php?t=386042 Last edited by dammitmitchell; 09-21-2009 at 09:31 PM. |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
