Power door conversion question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

joe231 · 11-15-2008, 11:54 PM

I have another question about converting to power. I'm going to get a pair of power doors off of a '85 tomorrow to convert my '80.
I realize I can just use the guts but my doors on my '80 have rust and someone repaired them by welding by the hinges and the door now lacks the adjustment needed to align properly with the fender and hood.
so my main question is about the wiring. does it unplug inside the cab somewhere, or do I need to cut wires? how many wires run to the drivers door, and how many run from the drivers to the passengers?
anyone have a schematic?
I would prefer not to stumble in blindly.
oh and also, do i have to pull the fenders to pull the doors?
Thanks for all the help, it is mucho appreciated.

BLE 'BURBAN · 11-16-2008, 04:57 AM

Quote:

Originally Posted by joe231

I have another question about converting to power. I'm going to get a pair of power doors off of a '85 tomorrow to convert my '80.
I realize I can just use the guts but my doors on my '80 have rust and someone repaired them by welding by the hinges and the door now lacks the adjustment needed to align properly with the fender and hood.
so my main question is about the wiring. does it unplug inside the cab somewhere, or do I need to cut wires? Yes it does. And you will need the harness that plugs into the harness and runs from side to side as well as the 30amp circuit breaker in the fuse block for the power windows and the power door lock relay that should be mounted to the top of the accelerator bracket. There are 2 power leads that pluginto the fuse panel and 2 ground leads that plug onto the 6-way ground plug behind the cluster on the left. Make sure when you install it into your truk that you properly mount the P/L relay otherwise they won't workhow many wires run to the drivers door, and how many run from the drivers to the passengers?
anyone have a schematic?
I would prefer not to stumble in blindly.
oh and also, do i have to pull the fenders to pull the doors?No you can simply unbolt the doors from the hinges. HOWEVER; In order to drill out the proper size holes in the proper locations on either side of the cab, it's best to loosen if not remove the fenders to get into it better. When I cut my suburban for power windows/locks/mirrors I didn't and I messed up the holes with the hole saw(egg shaped not round and had to glob in some silicone sealant around it.
Thanks for all the help, it is mucho appreciated.

Good Luck and have fun!!

73chevyman · 11-16-2008, 06:19 AM

Hey Joe send me some feed back cause I want to do the same thing with my 73 I'm lazy and rather push a button then lean over hahaha..

Mr79C10 · 11-16-2008, 07:42 AM

Hey Joe,,
When you do this, if ya could try to post a few pics. Im going to do the same thing to my 79

BLE 'BURBAN,
Great reply and very helpful, Thanks

joe231 · 11-16-2008, 10:48 AM

Quote:

Originally Posted by BLE 'BURBAN

Good Luck and have fun!!

Cool!
Thanks for the info!!

Quote:

Originally Posted by 73chevyman

Hey Joe send me some feed back cause I want to do the same thing with my 73 I'm lazy and rather push a button then lean over hahaha..

Quote:

Originally Posted by Mr79C10

Hey Joe,,
When you do this, if ya could try to post a few pics. Im going to do the same thing to my 79

BLE 'BURBAN,
Great reply and very helpful, Thanks

will do!

joe231 · 11-17-2008, 04:48 PM

BLE 'BURBAN, your info was very helpful!
I got the doors, the passenger side is junk and missing parts, including the power window motor, so I will probably look for another or just use my shell. Driver's door is complete minus the double power window switch. I got the complete power door harness, including that little PIA lock relay

I will get some pics on here of the pieces and parts and start another thread when i do the change over. should be relatively simple and straight forward, I've heard that one before

Thanks again for the info

BLE 'BURBAN · 11-23-2008, 05:19 AM

Anytime dude. I do what I can when I can to help out.
After all, what goes around, comes around.

Mr79C10 · 11-23-2008, 08:19 AM

Quote:

Originally Posted by BLE 'BURBAN

Anytime dude. I do what I can when I can to help out.
After all, what goes around, comes around.

So true....!

mainermikeyd · 11-24-2008, 09:00 PM

Pics Joe would be great, I am actually trying the same thing with a 82 sierra to 86 sierra full power options!!!!! Start mine thurs I'll letya know my progress bud!!!!

Mr79C10 · 12-09-2008, 09:25 PM

well, any pics yet?

joe231 · 12-09-2008, 09:35 PM

I can take pics of the parts sitting in my garage if ya like. i need a passenger door still, so I haven't started swapping yet

suicide 63 · 12-09-2008, 09:50 PM

whats taking so long ,oh by the just have to do this

joe231 · 12-09-2008, 09:54 PM

damn-it!
busted....would you like to be a deputy

joe231 · 12-09-2008, 10:15 PM

Name: DSC09901.jpg
Views: 503
Size: 30.8 KB

Name: DSC09902.jpg
Views: 500
Size: 23.6 KB

Name: DSC09903.jpg
Views: 509
Size: 19.3 KB

Name: DSC09904.jpg
Views: 502
Size: 22.6 KB

Name: DSC09905.jpg
Views: 505
Size: 23.4 KB

joe231 · 12-09-2008, 10:19 PM

Name: DSC09906.jpg
Views: 1278
Size: 25.9 KB

Name: DSC09910.jpg
Views: 496
Size: 26.8 KB

while I was there getting the doors, i grabbed this....
not sure what it is.
is it for the ESC or is it a DRAC?
'85 half ton, anyone need it?
Name: DSC09908.jpg
Views: 500
Size: 39.8 KB

Name: DSC09908.jpg
Views: 500
Size: 39.8 KB

Name: DSC09909.jpg
Views: 497
Size: 30.9 KB

Name: DSC09907.jpg
Views: 497
Size: 21.1 KB

joe231 · 12-11-2008, 03:16 PM

anyone?

BLE 'BURBAN · 12-15-2008, 04:04 AM

That there part is the cruise control module.

joe231 · 12-15-2008, 09:22 AM

cool, thanks

1987 Shortwide · 01-13-2009, 05:45 AM

This makes a little more sense now. Good thing you asked the question on the door wiring, because I now get to go dig around a salvage yard for the center harnes and circuit breaker.

locab36 · 02-25-2009, 03:22 PM

I'm doing the power door conversion right now. I drilled the holes in my non-power doors/cab today. Doors are off, fenders are on. The dimples from the factory sure help out. Here are some pics.

John

factory2wdblazer's · 02-26-2009, 03:50 AM

i recently did a power door conversion also. i used the complete door's off a 90 blazer and cut the top's off so the would my 73 blazer. i only have the harrness from the door jam's back...........from what i under stand i need a relay or some thing???? i did not remove the door's off the 90 blazer so i don't know how they where hooked up.....any body know

Twisted78SS · 02-26-2009, 04:09 AM

For anyone interested, I have what appears to be a complete power door lock and power window setup I am looking to part with.

I'll put it in the for sale area on Friday once I get some pictures.

(sorry to tread on your thread..)

joe231 · 09-25-2009, 08:39 PM

sorry I missed all this guys

Quote:

Originally Posted by locab36

I'm doing the power door conversion right now. I drilled the holes in my non-power doors/cab today. Doors are off, fenders are on. The dimples from the factory sure help out. Here are some pics.

John

Very nice....did you complete it?
I just swapped my '80 to a '73-'74 front end and to my suprise there where dimples where I needed to drill...I was quite happy...takes all the guess work out

Quote:

Originally Posted by factory2wdblazer's

i recently did a power door conversion also. i used the complete door's off a 90 blazer and cut the top's off so the would my 73 blazer. i only have the harrness from the door jam's back...........from what i under stand i need a relay or some thing???? i did not remove the door's off the 90 blazer so i don't know how they where hooked up.....any body know

did you get this figured out?

Quote:

Originally Posted by Twisted78SS

For anyone interested, I have what appears to be a complete power door lock and power window setup I am looking to part with.

I'll put it in the for sale area on Friday once I get some pictures.

(sorry to tread on your thread..)

did you sell the stuff?

bigblock73 · 09-25-2009, 09:07 PM

Quote:

Originally Posted by 73chevyman

Hey Joe send me some feed back cause I want to do the same thing with my 73 I'm lazy and rather push a button then lean over hahaha..

You can't put factory power windows in your 73...if it still has the original 73 doors. 73-76 doors are different than 77+...they were redesigned in 77 to accomodate PW/PL.

11-15-2008, 11:54 PM	#1
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Power door conversion question I have another question about converting to power. I'm going to get a pair of power doors off of a '85 tomorrow to convert my '80. I realize I can just use the guts but my doors on my '80 have rust and someone repaired them by welding by the hinges and the door now lacks the adjustment needed to align properly with the fender and hood. so my main question is about the wiring. does it unplug inside the cab somewhere, or do I need to cut wires? how many wires run to the drivers door, and how many run from the drivers to the passengers? anyone have a schematic? I would prefer not to stumble in blindly. oh and also, do i have to pull the fenders to pull the doors? Thanks for all the help, it is mucho appreciated. __________________ *CHEVY ONLY*

11-16-2008, 06:19 AM	#3
73chevyman Registered User Join Date: Nov 2008 Location: Lusby, MD Posts: 563	Re: Power door conversion question Hey Joe send me some feed back cause I want to do the same thing with my 73 I'm lazy and rather push a button then lean over hahaha.. __________________ http://67-72chevytrucks.com/vboard/group.php?groupid=37 73 C10 Fleetside If it ain't a Chevy it's foreign http://hotridesmag.com/

11-16-2008, 07:42 AM	#4
Mr79C10 It Is What It Is,,,, Join Date: Aug 2006 Location: The Gun Shine StateFlorida* Posts: 1,765	Re: Power door conversion question Hey Joe,, When you do this, if ya could try to post a few pics. Im going to do the same thing to my 79 BLE 'BURBAN, Great reply and very helpful, Thanks __________________ 79 C10 Short Box ST8 6 bang'r Lowered w/ 3" Control arms, 2" Lower Coils and 4" shackles and hangers W/ FLIP KIT __--__* 79 C-10 project* .........................__ ..............._____ l __\___ ..............\|_(O)_ \|___(O) ] FAQ INDEX Thread The Kulture My Rat Den

11-17-2008, 04:48 PM	#6
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: Power door conversion question BLE 'BURBAN, your info was very helpful! I got the doors, the passenger side is junk and missing parts, including the power window motor, so I will probably look for another or just use my shell. Driver's door is complete minus the double power window switch. I got the complete power door harness, including that little PIA lock relay I will get some pics on here of the pieces and parts and start another thread when i do the change over. should be relatively simple and straight forward, I've heard that one before Thanks again for the info __________________ *CHEVY ONLY*

11-23-2008, 05:19 AM	#7
BLE 'BURBAN In the Forgotten far North. Join Date: Jul 2007 Location: Anchorage, Alaska Posts: 2,627	Re: Power door conversion question Anytime dude. I do what I can when I can to help out. After all, what goes around, comes around. __________________ 1987 R3500 CREW CAB DUALLY (BIG RED)Acquired 06/12/2015 1990 chevy suburban V2500 5.7L My cluster Mods-Nov 2007 overhead console Stereo install Round 2 Aug 2009 Heated/turn signal mirror upgrade

11-24-2008, 09:00 PM	#9
mainermikeyd Registered User Join Date: Sep 2008 Location: Limington, ME Posts: 290	Re: Power door conversion question Pics Joe would be great, I am actually trying the same thing with a 82 sierra to 86 sierra full power options!!!!! Start mine thurs I'll letya know my progress bud!!!! __________________ Once a Marine Always a Marine OOH-RAH GM Fanatic 1982 K20 4" Rancho lift 350cid, edelbrock performer intake 1405 carb, hedman headers, TH350, " Wheres the MUD!!!!!!!!!!" 1986 c30 camper special 454, th400 (for sale) 1984 K10 Big Ten (project) needs motor 1984 C10 355, 700r4, (project) needs shortbox bed

12-09-2008, 09:25 PM	#10
Mr79C10 It Is What It Is,,,, Join Date: Aug 2006 Location: The Gun Shine StateFlorida* Posts: 1,765	Re: Power door conversion question well, any pics yet? __________________ 79 C10 Short Box ST8 6 bang'r Lowered w/ 3" Control arms, 2" Lower Coils and 4" shackles and hangers W/ FLIP KIT __--__* 79 C-10 project* .........................__ ..............._____ l __\___ ..............\|_(O)_ \|___(O) ] FAQ INDEX Thread The Kulture My Rat Den

12-09-2008, 09:35 PM	#11
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: Power door conversion question I can take pics of the parts sitting in my garage if ya like. i need a passenger door still, so I haven't started swapping yet __________________ *CHEVY ONLY*

12-09-2008, 09:50 PM	#12
suicide 63 Registered User Join Date: Nov 2007 Location: peculiar mo Posts: 219	Re: Power door conversion question whats taking so long ,oh by the just have to do this __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=304940

12-09-2008, 09:54 PM	#13
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: Power door conversion question damn-it! busted....would you like to be a deputy __________________ *CHEVY ONLY*

12-09-2008, 10:15 PM	#14
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: Power door conversion question __________________ *CHEVY ONLY*

12-09-2008, 10:19 PM	#15
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: Power door conversion question while I was there getting the doors, i grabbed this.... not sure what it is. is it for the ESC or is it a DRAC? '85 half ton, anyone need it? __________________ *CHEVY ONLY* Last edited by joe231; 12-09-2008 at 10:22 PM.

12-11-2008, 03:16 PM	#16
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: Power door conversion question anyone? __________________ *CHEVY ONLY*

12-15-2008, 04:04 AM	#17
BLE 'BURBAN In the Forgotten far North. Join Date: Jul 2007 Location: Anchorage, Alaska Posts: 2,627	Re: Power door conversion question That there part is the cruise control module. __________________ 1987 R3500 CREW CAB DUALLY (BIG RED)Acquired 06/12/2015 1990 chevy suburban V2500 5.7L My cluster Mods-Nov 2007 overhead console Stereo install Round 2 Aug 2009 Heated/turn signal mirror upgrade

12-15-2008, 09:22 AM	#18
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: Power door conversion question cool, thanks __________________ *CHEVY ONLY*



Register or Log In To remove these advertisements.

01-13-2009, 05:45 AM	#19
1987 Shortwide Senior Member Join Date: Feb 2003 Location: Wichita KS Posts: 610	Re: Power door conversion question This makes a little more sense now. Good thing you asked the question on the door wiring, because I now get to go dig around a salvage yard for the center harnes and circuit breaker. __________________ ~Steve~ Friesen High Performance Auto and Graphics Toy: 87 Shortwide, 406 smallblock with a little boost My 87 buildup Daily Driver: 99 Sierra SLE 4X4. Black on Black and harder than hell to keep clean.

02-25-2009, 03:22 PM	#20
locab36 Registered User Join Date: Jun 2004 Location: Midland, MI Posts: 265	Re: Power door conversion question I'm doing the power door conversion right now. I drilled the holes in my non-power doors/cab today. Doors are off, fenders are on. The dimples from the factory sure help out. Here are some pics. John Attached Images __________________ Locab36 1936 low cab 1/2 ton 1956 BMW R25/3 1968 Moto Guzzi V7 1969 BMW R100/2 1986 Silverado SWB 2007 Harley FLHTP 2011 GMC SWB 4x4 Z71 http://www.flickr.com/photos/locab36...7623329816080/

02-26-2009, 03:50 AM	#21
factory2wdblazer's Registered User Join Date: Sep 2008 Location: northern, califorina Posts: 199	Re: Power door conversion question i recently did a power door conversion also. i used the complete door's off a 90 blazer and cut the top's off so the would my 73 blazer. i only have the harrness from the door jam's back...........from what i under stand i need a relay or some thing???? i did not remove the door's off the 90 blazer so i don't know how they where hooked up.....any body know

02-26-2009, 04:09 AM	#22
Twisted78SS Wide n'Low Join Date: Jan 2007 Location: La Center, WA Posts: 1,511	Re: Power door conversion question For anyone interested, I have what appears to be a complete power door lock and power window setup I am looking to part with. I'll put it in the for sale area on Friday once I get some pictures. (sorry to tread on your thread..) __________________ Trippin Hazard.. 67 swb, Gold Member.. 68 Suburban Air Force Retired

Register or Log In To remove these advertisements.