Header Question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

BAGNDRAGIT · 12-09-2009, 07:05 PM

ok guys, i have searched with no luck, and i have seen it, so i know im not crazy haha. i am looking for a set of headers that will clear the factory clutch linkage on a 67 2wd w/ a 327, and they have to be above the framerails., hence why i am changing them. they drag on the ground.

Thanks in advance!!

69GMCLonghorn · 12-09-2009, 07:55 PM

It's going to have to be shorty headers from what I know. All the long tube headers I've seen run below the frame rails. I guess that's an advantage to not lowering my truck. They could've hung down a foot with no worries. Good luck! I'm sure if they're out there someone will know what to use.

unclewatts · 12-09-2009, 10:07 PM

When I bought my Headman headers, the guy asked to see my clutch linkage. He told me that the clutch linkage was located in 2 different locations on our trucks. Hedman makes 2 different header models depending on the location of the crosshaft and they're both long pipe headers. When I had them installed they fit perfectly.

BAGNDRAGIT · 12-10-2009, 02:04 PM

Quote:

Originally Posted by unclewatts

When I bought my Headman headers, the guy asked to see my clutch linkage. He told me that the clutch linkage was located in 2 different locations on our trucks. Hedman makes 2 different header models depending on the location of the crosshaft and they're both long pipe headers. When I had them installed they fit perfectly.

ok so i would need to call headman to see what type i have, unless you know the difference?

and the longtubes you have hang below the frame correct.

i thought sanderson made a pair that would fit around the linkage, and were shorty.

BTW Thanks unclewatts and 69GMCLonghorn

marcsRX · 12-10-2009, 02:14 PM

I ordered these after getting a set of long tubes from Summit. I had the same issue as you...

Quote:

Early Classic is proud to offer the highest quality, American-made Small Block Headers available for 1967-'72 GM small block trucks. These new mid-length headers are swept rearward and dump below the firewall eliminating ground clearance problems for lowered trucks.

These 16 gauge, mandrel bent beauties come with the only patented leak-free flange on the market. As an added bonus, a ceramic thermal barrier coating has been applied inside and out for years of trouble-free performance. (Pair)

BAGNDRAGIT · 12-10-2009, 02:49 PM

Thank you so much marcsRX

i was racking my brain trying to track them down.

much appreciated.

marcsRX · 12-10-2009, 02:56 PM

That's why this is called a "community".

Post pics when its all buttoned up!

BAGNDRAGIT · 12-10-2009, 03:16 PM

Quote:

Originally Posted by marcsRX

That's why this is called a "community".

Post pics when its all buttoned up!

community, more like new family

and i sure will. gotta finish the bags first..

unclewatts · 12-10-2009, 11:05 PM

Quote:

Originally Posted by BAGNDRAGIT

ok so i would need to call headman to see what type i have, unless you know the difference?

and the longtubes you have hang below the frame correct.

i thought sanderson made a pair that would fit around the linkage, and were shorty.

BTW Thanks unclewatts and 69GMCLonghorn

Yes, they hang down well below the frame. P.S. Your very welcome.

ace of shades · 12-11-2009, 01:11 AM

I'm not too sure about the mouse motors; but I know that when I swapped over to my elephant I'm running a set of chevell shortie headers. They dump out pointing towards the ground but with a simple cut, weld, drive you have it made

zammer · 01-31-2010, 10:12 PM

Hello,

I just bought a set of the sanderson headers from Early Classic Ent, and I am having troubles clearing my clutch link on my 4 speed trans. Anyone else come across this issue?
Does anyone have pics of the drivers side sanderson header installed with a 4 speed trans in a 67-72 c10?

I have a 71 2wd blazer... any help would be great

thanks!

dznucks · 02-01-2010, 08:19 AM

I just installed these edelbrocks on a '69 with a stock clutch linkage.

i found the best price on the ceramic coated ones at ajusa.com

zammer · 02-01-2010, 10:04 AM

do those headers clear the frame so you can use them on a lowered truck?

dznucks · 02-01-2010, 03:16 PM

zammer, if your asking about the edelbrock hotrod headers. yes they will clear the frame with plenty of room.

here is the post with pics. you can get an idea of how close they come to the frame. my truck is lowered 3" in the front (soon to be bagged) and the back is bagged. The header flanges do not sit any lower than the lowest part of your frame.

http://67-72chevytrucks.com/vboard/s...d.php?t=380456

MTtruck · 02-01-2010, 07:25 PM

I used a set of pretty long headers on my 68 4x4 and had to do some fairly simple mods to my linkage. not to bad if you know how to weld. ill post a pic of my modification soon.

snaus32 · 02-02-2010, 11:48 AM

Quote:

Originally Posted by marcsRX

I ordered these after getting a set of long tubes from Summit. I had the same issue as you...

is there a part numbers for those? I couldn't find them.

12-09-2009, 07:05 PM	#1
BAGNDRAGIT Just Not Low Enough! Join Date: Mar 2009 Location: Phoenix, AZ Posts: 525	Header Question ok guys, i have searched with no luck, and i have seen it, so i know im not crazy haha. i am looking for a set of headers that will clear the factory clutch linkage on a 67 2wd w/ a 327, and they have to be above the framerails., hence why i am changing them. they drag on the ground. Thanks in advance!! __________________ NEED ELECTRICAL HELP? ASK ME! 67-72 Full Wiring Diagrams Lots Of Info, TAKE A LOOK 1967 Chevy C-10 Shortbox Bagged 327 4spd Previous: 1971 Chevy C-10 Short Sep I6 Auto (Traded) 1973 Chevy C-20 THE REDNECK BATTLE TRUCK 2001 Chevy Silverado 2Dr 5.3L Shortbox. R.I.P. 1969 Volkswagen Bug This is my first meeting, I have a horsepower problem.

12-09-2009, 07:55 PM	#2
69GMCLonghorn Registered User Join Date: Dec 2006 Location: Porter Ranch, CA Posts: 978	Re: Header Question It's going to have to be shorty headers from what I know. All the long tube headers I've seen run below the frame rails. I guess that's an advantage to not lowering my truck. They could've hung down a foot with no worries. Good luck! I'm sure if they're out there someone will know what to use.

12-09-2009, 10:07 PM	#3
unclewatts 70 Chevrolet=Obsession Join Date: Jun 2009 Location: nice ca Posts: 1,067	Re: Header Question When I bought my Headman headers, the guy asked to see my clutch linkage. He told me that the clutch linkage was located in 2 different locations on our trucks. Hedman makes 2 different header models depending on the location of the crosshaft and they're both long pipe headers. When I had them installed they fit perfectly. __________________ I'm Just like my truck. Old, Ugly and Grouchy. Except my truck starts easily in the morning and doesn't smoke! IT'S NOT EASY BEING GREEN! -Kermit the frog 1970 Chevrolet C-10 Longbed Stepside : 350, Muncie M20, 3.08 GM corp. positraction Forest green exterior/light green interior(Where all my money goes) 1996 Toyota Corolla (Parts runner)

12-10-2009, 02:49 PM	#6
BAGNDRAGIT Just Not Low Enough! Join Date: Mar 2009 Location: Phoenix, AZ Posts: 525	Re: Header Question Thank you so much marcsRX i was racking my brain trying to track them down. much appreciated. __________________ NEED ELECTRICAL HELP? ASK ME! 67-72 Full Wiring Diagrams Lots Of Info, TAKE A LOOK 1967 Chevy C-10 Shortbox Bagged 327 4spd Previous: 1971 Chevy C-10 Short Sep I6 Auto (Traded) 1973 Chevy C-20 THE REDNECK BATTLE TRUCK 2001 Chevy Silverado 2Dr 5.3L Shortbox. R.I.P. 1969 Volkswagen Bug This is my first meeting, I have a horsepower problem.

12-10-2009, 02:56 PM	#7
marcsRX 68 C10 SWB Join Date: Nov 2009 Location: Chicago Posts: 216	Re: Header Question That's why this is called a "community". Post pics when its all buttoned up! __________________ "How much physical pain do you go through on a daily basis that you can directly attribute to your lack of intelligence?" -R0bman

12-11-2009, 01:11 AM	#10
ace of shades NEWBIE!! Join Date: Mar 2009 Location: Prineville OR Posts: 114	Re: Header Question I'm not too sure about the mouse motors; but I know that when I swapped over to my elephant I'm running a set of chevell shortie headers. They dump out pointing towards the ground but with a simple cut, weld, drive you have it made __________________ Water is for the weak I don't like cocaine.. I just like the smell of it "Well there might be a dime up a goats ass too, but I ain't looken" - Grandpa VolksRods

01-31-2010, 10:12 PM	#11
zammer Addicted user Join Date: Sep 2009 Location: Edmonton, Alberta Posts: 370	Re: Header Question Hello, I just bought a set of the sanderson headers from Early Classic Ent, and I am having troubles clearing my clutch link on my 4 speed trans. Anyone else come across this issue? Does anyone have pics of the drivers side sanderson header installed with a 4 speed trans in a 67-72 c10? I have a 71 2wd blazer... any help would be great thanks!

02-01-2010, 08:19 AM	#12
dznucks Registered User Join Date: Feb 2006 Location: Smyrna, Ga Posts: 1,647	Re: Header Question I just installed these edelbrocks on a '69 with a stock clutch linkage. i found the best price on the ceramic coated ones at ajusa.com Attached Images Last edited by dznucks; 02-01-2010 at 08:19 AM.

02-01-2010, 10:04 AM	#13
zammer Addicted user Join Date: Sep 2009 Location: Edmonton, Alberta Posts: 370	Re: Header Question do those headers clear the frame so you can use them on a lowered truck?

02-01-2010, 03:16 PM	#14
dznucks Registered User Join Date: Feb 2006 Location: Smyrna, Ga Posts: 1,647	Re: Header Question zammer, if your asking about the edelbrock hotrod headers. yes they will clear the frame with plenty of room. here is the post with pics. you can get an idea of how close they come to the frame. my truck is lowered 3" in the front (soon to be bagged) and the back is bagged. The header flanges do not sit any lower than the lowest part of your frame. http://67-72chevytrucks.com/vboard/s...d.php?t=380456 Last edited by dznucks; 02-01-2010 at 03:21 PM.

02-01-2010, 07:25 PM	#15
MTtruck Registered User Join Date: Jul 2009 Location: Bozeman, Mt Posts: 59	Re: Header Question I used a set of pretty long headers on my 68 4x4 and had to do some fairly simple mods to my linkage. not to bad if you know how to weld. ill post a pic of my modification soon. __________________ Paul"Give old trucks a second chance"



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.