Stock A arms blasted and powder coated. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

phantom dually · 04-29-2003, 12:23 AM

I have a set of stock arms from a 83 1/2 ton. They have been blasted and powder coated black. The lower arm have had the stop removed to clear a air bag. They are a great way to swap out your old ones with no downtime. The shaft are also included and are powdered as well. I do have all new bushings and balljoints that can go for a very reasonable price. Arms only will take $130 shipped. These should fit all 1/2 ton and others from 60's to mid 80's. Balljoints and bushings will go for a additional $100 shipped. 4 lower bushings 4 upper bushings and 4 new moog ball joints. Ball joints alone were $100. All parts are new!!

phantom dually · 04-29-2003, 12:24 AM

lowers arms

78SilveradoSWB · 04-29-2003, 01:58 PM

Are the "A" arm bushings Energy Suspension, PST, or OEM?

stepn67 · 04-29-2003, 03:26 PM

Hey Phantom,
Been looking for a set for my '67 - But would the shipping cost to AZ (85712) kill me?

phantom dually · 04-29-2003, 09:55 PM

I will sell for $130 shipped as said!!

phantom dually · 05-01-2003, 04:14 PM

The bushings and ball joints have been Sold But I still have the a arms and shafts.

low 84 · 05-01-2003, 08:52 PM

okay. i am intrested but what exactly is it? 4 arms and shafts. are the shafts installed on the arms with bushings or are they apart? and how good of a job is the powdercoating, any dust or junk in it?

i will probly take them off you hands. thanks

low 84 · 05-02-2003, 12:19 PM

TTT

phantom dually · 05-02-2003, 01:12 PM

Im new to this so what is TTT. The arms are not 100% perfect but a great step over stock. I have all the arms and the 2 lower shafts. I do not have the upper shafts. They are really clean. The uppers look better than the lowers becuase of a few scraps when i took off the bump stops.

78SilveradoSWB · 05-02-2003, 01:48 PM

TTT or ^^^ is used to bump the post up near the top for visability.

low 84 · 05-02-2003, 09:01 PM

i'll take em. lets move this to pm

low 84 · 05-03-2003, 11:38 AM

did you get my pm? please respond if you want to sell these.

phantom dually · 05-03-2003, 01:46 PM

Sent you e mail your pm box is full.

04-29-2003, 12:23 AM	#1
phantom dually Project92 SWB stepside Join Date: Feb 2003 Location: Louisville KY Posts: 4,792	Stock A arms blasted and powder coated. I have a set of stock arms from a 83 1/2 ton. They have been blasted and powder coated black. The lower arm have had the stop removed to clear a air bag. They are a great way to swap out your old ones with no downtime. The shaft are also included and are powdered as well. I do have all new bushings and balljoints that can go for a very reasonable price. Arms only will take $130 shipped. These should fit all 1/2 ton and others from 60's to mid 80's. Balljoints and bushings will go for a additional $100 shipped. 4 lower bushings 4 upper bushings and 4 new moog ball joints. Ball joints alone were $100. All parts are new!! Attached Images __________________ 92 C1500 stepside 496 Stroker Competiton Engineering Ladder bars/QA1 coilovers. Dana 60 rear with 4.10 gear and posi. Bonspeed Palisade 20x12 in rear w/335/30/20 and 20x8.5 front w/245/40/20. 5/8 drop with Belltech springs/DJM spindles/drop shocks. WWS Progress thread http://67-72chevytrucks.com/vboard/s...d.php?t=140448

04-29-2003, 12:24 AM	#2
phantom dually Project92 SWB stepside Join Date: Feb 2003 Location: Louisville KY Posts: 4,792	lowers lowers arms Attached Images __________________ 92 C1500 stepside 496 Stroker Competiton Engineering Ladder bars/QA1 coilovers. Dana 60 rear with 4.10 gear and posi. Bonspeed Palisade 20x12 in rear w/335/30/20 and 20x8.5 front w/245/40/20. 5/8 drop with Belltech springs/DJM spindles/drop shocks. WWS Progress thread http://67-72chevytrucks.com/vboard/s...d.php?t=140448

04-29-2003, 01:58 PM	#3
78SilveradoSWB Senior Member Join Date: Apr 2002 Location: Beaverton, OR Posts: 1,615	Are the "A" arm bushings Energy Suspension, PST, or OEM? __________________ Mitch 1978 Chevrolet Silverado C 10 454 BB, TH400

04-29-2003, 09:55 PM	#5
phantom dually Project92 SWB stepside Join Date: Feb 2003 Location: Louisville KY Posts: 4,792	I will sell for $130 shipped as said!! __________________ 92 C1500 stepside 496 Stroker Competiton Engineering Ladder bars/QA1 coilovers. Dana 60 rear with 4.10 gear and posi. Bonspeed Palisade 20x12 in rear w/335/30/20 and 20x8.5 front w/245/40/20. 5/8 drop with Belltech springs/DJM spindles/drop shocks. WWS Progress thread http://67-72chevytrucks.com/vboard/s...d.php?t=140448

05-01-2003, 04:14 PM	#6
phantom dually Project92 SWB stepside Join Date: Feb 2003 Location: Louisville KY Posts: 4,792	The bushings and ball joints have been Sold But I still have the a arms and shafts. __________________ 92 C1500 stepside 496 Stroker Competiton Engineering Ladder bars/QA1 coilovers. Dana 60 rear with 4.10 gear and posi. Bonspeed Palisade 20x12 in rear w/335/30/20 and 20x8.5 front w/245/40/20. 5/8 drop with Belltech springs/DJM spindles/drop shocks. WWS Progress thread http://67-72chevytrucks.com/vboard/s...d.php?t=140448

04-29-2003, 03:26 PM	#4
stepn67 Junior Member Join Date: Dec 2002 Location: Tucson, AZ Posts: 140	Hey Phantom, Been looking for a set for my '67 - But would the shipping cost to AZ (85712) kill me?

05-01-2003, 08:52 PM	#7
low 84 Registered User Join Date: Jan 2002 Location: Houston, TX Posts: 2,144	okay. i am intrested but what exactly is it? 4 arms and shafts. are the shafts installed on the arms with bushings or are they apart? and how good of a job is the powdercoating, any dust or junk in it? i will probly take them off you hands. thanks __________________ '51 F100, backhalf with a narrowed 9 and coil overs, 18.5" mickeys, monte front clip, +400" sbc in the works '05 1500 Crew Cab RIP '84 swb 5/7 drop, solid cammed 408 w/ fully ported dart heads, th350 w/ 10 inch hughes, 12 bolt w/ 3.73 richmonds and a locker '80 swb 4x4 in progress: 7" lift, 350 th350/np205, d44 and 1.5" ORD tie rod, 14BFF w/discs , armored diff covers, 40" MTR's

05-02-2003, 12:19 PM	#8
low 84 Registered User Join Date: Jan 2002 Location: Houston, TX Posts: 2,144	TTT __________________ '51 F100, backhalf with a narrowed 9 and coil overs, 18.5" mickeys, monte front clip, +400" sbc in the works '05 1500 Crew Cab RIP '84 swb 5/7 drop, solid cammed 408 w/ fully ported dart heads, th350 w/ 10 inch hughes, 12 bolt w/ 3.73 richmonds and a locker '80 swb 4x4 in progress: 7" lift, 350 th350/np205, d44 and 1.5" ORD tie rod, 14BFF w/discs , armored diff covers, 40" MTR's

05-02-2003, 01:12 PM	#9
phantom dually Project92 SWB stepside Join Date: Feb 2003 Location: Louisville KY Posts: 4,792	Im new to this so what is TTT. The arms are not 100% perfect but a great step over stock. I have all the arms and the 2 lower shafts. I do not have the upper shafts. They are really clean. The uppers look better than the lowers becuase of a few scraps when i took off the bump stops. __________________ 92 C1500 stepside 496 Stroker Competiton Engineering Ladder bars/QA1 coilovers. Dana 60 rear with 4.10 gear and posi. Bonspeed Palisade 20x12 in rear w/335/30/20 and 20x8.5 front w/245/40/20. 5/8 drop with Belltech springs/DJM spindles/drop shocks. WWS Progress thread http://67-72chevytrucks.com/vboard/s...d.php?t=140448

05-02-2003, 01:48 PM	#10
78SilveradoSWB Senior Member Join Date: Apr 2002 Location: Beaverton, OR Posts: 1,615	TTT or ^^^ is used to bump the post up near the top for visability. __________________ Mitch 1978 Chevrolet Silverado C 10 454 BB, TH400

05-02-2003, 09:01 PM	#11
low 84 Registered User Join Date: Jan 2002 Location: Houston, TX Posts: 2,144	i'll take em. lets move this to pm __________________ '51 F100, backhalf with a narrowed 9 and coil overs, 18.5" mickeys, monte front clip, +400" sbc in the works '05 1500 Crew Cab RIP '84 swb 5/7 drop, solid cammed 408 w/ fully ported dart heads, th350 w/ 10 inch hughes, 12 bolt w/ 3.73 richmonds and a locker '80 swb 4x4 in progress: 7" lift, 350 th350/np205, d44 and 1.5" ORD tie rod, 14BFF w/discs , armored diff covers, 40" MTR's

05-03-2003, 11:38 AM	#12
low 84 Registered User Join Date: Jan 2002 Location: Houston, TX Posts: 2,144	did you get my pm? please respond if you want to sell these. __________________ '51 F100, backhalf with a narrowed 9 and coil overs, 18.5" mickeys, monte front clip, +400" sbc in the works '05 1500 Crew Cab RIP '84 swb 5/7 drop, solid cammed 408 w/ fully ported dart heads, th350 w/ 10 inch hughes, 12 bolt w/ 3.73 richmonds and a locker '80 swb 4x4 in progress: 7" lift, 350 th350/np205, d44 and 1.5" ORD tie rod, 14BFF w/discs , armored diff covers, 40" MTR's

05-03-2003, 01:46 PM	#13
phantom dually Project92 SWB stepside Join Date: Feb 2003 Location: Louisville KY Posts: 4,792	Sent you e mail your pm box is full. __________________ 92 C1500 stepside 496 Stroker Competiton Engineering Ladder bars/QA1 coilovers. Dana 60 rear with 4.10 gear and posi. Bonspeed Palisade 20x12 in rear w/335/30/20 and 20x8.5 front w/245/40/20. 5/8 drop with Belltech springs/DJM spindles/drop shocks. WWS Progress thread http://67-72chevytrucks.com/vboard/s...d.php?t=140448



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.