|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
02-09-2010, 08:43 PM
|
#1 |
|
Registered User
Join Date: Feb 2010
Location: Nanticoke, Pa.
Posts: 12
|
dana 44-5F closed knuckle front end
Anyone know where to get replacement parts for this diff. Looking for knuckle seals, gaskets etc. Thanks
|
|
|
|
02-09-2010, 09:01 PM
|
#2 |
|
Registered User
Join Date: Jan 2010
Location: GREENEVILLE TENNESSEE
Posts: 1,310
|
Re: dana 44-5F closed knuckle front end
If you do have the closed knuckle front 44 you are better off ordering the front knuckle seals for a 1968 1970 jeep wagoneer...gladiator...ect i got mine from jc whitney..for my 69 K/20 front c/k 44 and these are the same parts...fit perfect
Last edited by 70BLAZERX2; 02-09-2010 at 09:02 PM. |
|
|
|
|
02-09-2010, 09:06 PM
|
#3 |
|
Registered User
Join Date: Feb 2010
Location: Nanticoke, Pa.
Posts: 12
|
Re: dana 44-5F closed knuckle front end
Thanks, I'll check them out.
|
|
|
|
|
02-09-2010, 09:09 PM
|
#4 |
|
Registered User
Join Date: Jan 2010
Location: GREENEVILLE TENNESSEE
Posts: 1,310
|
Re: dana 44-5F closed knuckle front end
I know its wierd, but this way you can get them...and they were not that much anyway...it is still a dana44 no matter what it was in,unless a ford front then its reverse rotation high pinion.
|
|
|
|
|
02-09-2010, 10:07 PM
|
#5 |
|
Registered User
Join Date: Feb 2010
Location: Nanticoke, Pa.
Posts: 12
|
Re: dana 44-5F closed knuckle front end
Found them thanks again. Anything else on the knuckle I should get. I never took one apart, I only worked on 44's with ball joints 1975 up.
|
|
|
|
|
02-10-2010, 01:31 PM
|
#6 |
|
Registered User
Join Date: Jan 2010
Location: GREENEVILLE TENNESSEE
Posts: 1,310
|
Re: dana 44-5F closed knuckle front end
get an older book for the 68-70 trucks..I do have some of them if you cannot find them..I could e-mail you some exploded pics if needed..I have a factory service manual for these trucks
|
|
|
|
|
02-10-2010, 06:57 PM
|
#7 |
|
Registered User
Join Date: Feb 2010
Location: Nanticoke, Pa.
Posts: 12
|
Re: dana 44-5F closed knuckle front end
I am ordering the service manual today. Pics would help if you can send some. LMC truck doesn't have the parts i'm looking for. Any other parts places you know of? Thanks again.
|
|
|
|
|
02-10-2010, 09:39 PM
|
#8 |
|
Senior Member
Join Date: Jul 2004
Location: Clarks Hill, Indiana
Posts: 733
|
Re: dana 44-5F closed knuckle front end
i picked up a book called the chevy owners bible, or something similar to that. I was the most info on a closed knuckle axle i had seen at the time.
__________________
1969 K10 - V8, 465, 205, 12 bolt, D44 2002-current 1969 K20 - V8, 465, 221, Eaton, D44 2012-current Nothin' but drums on all 4 corners! past horses in the stable 72 C10-short step (97-02), 68 C10-long fleet (06-12) |
|
|
|
|
02-11-2010, 06:36 PM
|
#9 |
|
Firefighter
Join Date: Feb 2001
Location: Yellville, Ar, USA
Posts: 1,943
|
Re: dana 44-5F closed knuckle front end
Try www.quad4x4.com Part #QU40188
__________________
'72 Chevy SWB 350 Auto '67 GMC LWB 350 4 speed '70 Chevy 4x4 Stepside 350 Auto Yellville, Ar. USA  
|
|
|
|
|
02-12-2010, 02:47 AM
|
#10 |
|
Registered User
 Join Date: Feb 2010
Location: Santa Clara Utah
Posts: 85
|
Re: dana 44-5F closed knuckle front end
Is there a any difference in the dana 44 open knuckle front axles? My 72 k10 has the dana 44 with -5F in the lower right hand corner. My dads 72 k5 blazer has 44 in the lower right hand corner. Are they different?
__________________
1972 K10 4wd Swb 350, 4 speed, 205 t-case Sold 1971 Cheyenne 2wd Lwb 350 4 speed Sold 1972 K5 blazer 4WD auto A/C |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
