Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
03-22-2010, 02:59 PM | #1 |
Registered User
Join Date: Feb 2010
Location: DANA POINT CA
Posts: 256
|
Round Cup holders for factory console
I have been seeing a lot of factory consoles with round cup holder does anyone know where to get these ??
__________________
ScoobyDoobyDoo |
03-22-2010, 03:19 PM | #2 |
Registered User
Join Date: Oct 2007
Location: Sammamish, WA
Posts: 2,115
|
Re: Round Cup holders for factory console
Not 100% positive, but they were used from 75 up to early 80's? Watch the board in the foresale section
|
03-22-2010, 03:27 PM | #3 |
SKINNY TIRES RULE!
Join Date: Sep 2001
Location: Bothell, WA
Posts: 11,038
|
Re: Round Cup holders for factory console
Round cup holders are second generation. You can post a wanted to buy on the board or possibly find them in junk yards. LMC may sell repops.
__________________
bouncytruck 1972 K5 The Hauler 1994 K1500 Suburban The Daily2010 Kia Soul Wife's Ride2014 Fiat 500L |
03-22-2010, 04:11 PM | #4 |
Registered User
Join Date: Feb 2010
Location: DANA POINT CA
Posts: 256
|
Re: Round Cup holders for factory console
Ok the consoles I have seen were 69-72 consoles with the seam down the middle
__________________
ScoobyDoobyDoo |
03-22-2010, 04:26 PM | #5 |
Registered User
Join Date: Jun 2003
Location: Calgary AB
Posts: 110
|
Re: Round Cup holders for factory console
Not completely sure about "seam down the middle", but I had a 79 Blazer that had the cup holders in the console. Looked the same as my 71 otherwise.
__________________
You can't get out if ya don't get in |
03-22-2010, 05:08 PM | #6 |
SKINNY TIRES RULE!
Join Date: Sep 2001
Location: Bothell, WA
Posts: 11,038
|
Re: Round Cup holders for factory console
The consoles are the same with the exception of the cup holders vs. seat belt holders. The consoles can be split in half horizontally, but the upper part is usually where most of the damage and wear is. I believe a few guys have cut the cup holder part out of a new console and put it in place of the seat belt holder part.
__________________
bouncytruck 1972 K5 The Hauler 1994 K1500 Suburban The Daily2010 Kia Soul Wife's Ride2014 Fiat 500L |
03-22-2010, 07:59 PM | #7 |
Registered User
Join Date: May 2007
Location: San Antonio
Posts: 993
|
Re: Round Cup holders for factory console
I bought a console from junkyard and it was out of a second gen. I think it was a '75 and it was exactly the same as my '72 with the exception of the cupholders. It bolted right in. Mario.
|
03-22-2010, 08:12 PM | #8 |
Registered User
Join Date: Feb 2010
Location: DANA POINT CA
Posts: 256
|
Re: Round Cup holders for factory console
sweet thanks
__________________
ScoobyDoobyDoo |
03-23-2010, 10:48 AM | #9 |
Registered User
Join Date: Jan 2010
Location: CA
Posts: 78
|
Re: Round Cup holders for factory console
I just bought the reproduction console from classic industries for 129.00. It is from the 73-75 body but fits perfect in my 72. Looks sweet... Hope this helps
|
Bookmarks |
|
|