|
04-26-2010, 09:10 AM
|
#1 |
|
Registered User
Join Date: Nov 2009
Location: Arlington,TX
Posts: 88
|
taking out 350
I have a '75 burb. Do I have to remove the hood to take out the 350? Also any other tips would be appreciated. I am a total rookie.
|
|
|
|
04-26-2010, 09:21 AM
|
#2 |
|
Slots go on anything!
Join Date: May 2003
Location: Richardson, TX
Posts: 5,957
|
Re: taking out 350
That will help out a lot. Depending on what you are planning on using, you can unbolt the A/C and power steering from the engine to remove it, then come back for them later. I am guessing you are stripping it as a donor for your pickup? If that is the case, it may be faster and easier to remove the front end, and pull the engine and transmission as a unit.
__________________
1974 Jimmy- 5.3/4L80e/NP241 |
|
|
|
|
04-26-2010, 09:23 AM
|
#3 |
|
Registered User
Join Date: Nov 2009
Location: Arlington,TX
Posts: 88
|
Re: taking out 350
That is the plan(donor). So remove the front end first?
|
|
|
|
|
04-26-2010, 09:32 AM
|
#4 |
|
One foot in front of the other
 
Join Date: Aug 2008
Location: Parrottsville, TN
Posts: 5,442
|
Re: taking out 350
Take pictures at different angles before you start and save ALL the bolts.
|
|
|
|
|
04-26-2010, 09:37 AM
|
#5 |
|
Registered User
Join Date: Nov 2009
Location: Arlington,TX
Posts: 88
|
Re: taking out 350
Will do thanks.
|
|
|
|
|
04-26-2010, 10:25 AM
|
#6 |
|
Slots go on anything!
Join Date: May 2003
Location: Richardson, TX
Posts: 5,957
|
Re: taking out 350
If you are planning on parting out the 'burb, and don't care how it goes back together, I would pull the clip, just to get it out of the way. That will make it easier to get to the suspension I am assuming you will use, too. I like the extra room to work, too.
__________________
1974 Jimmy- 5.3/4L80e/NP241 |
|
|
|
|
04-26-2010, 11:53 AM
|
#7 |
|
Robert Olson Transport
 
Join Date: Oct 2002
Location: recent transplant to NC USA
Posts: 20,310
|
Re: taking out 350
you dont tell us alot here but i agree with johnboy pull the clip if youre scrapping the burb as it goes easier and if you want to make it easy pull the trans with it.
If youre not pulling the trans too and this is a motor swap, make sure you remember to get the torque convertor bolts as the first swap i did i forgot them You have to pull the radiator and at the very least the hood. I also find it a heck of alot easier to leave the exhaust manifolds in as the bolts that hold them onto the block are alot easier to break loose and unbolt than the flange bolts like the other poster said make sure you label things with masking tape and labelled sandwich bags with the bolts are another good idea also the stupidest advice can be the best advice.. make sure the truck is properly supported and blocked before you start this job
__________________
Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!! |
|
|
|
|
04-26-2010, 01:41 PM
|
#8 |
|
Registered User
Join Date: Nov 2009
Location: Arlington,TX
Posts: 88
|
Re: taking out 350
Yes I am scrapping it. thanks for the good advice.
|
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
