Z-ing a frame (REAR) - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Malibob · 06-08-2010, 07:33 PM

Can you z the rear of the frame? What I am thinking is right behind the cab before the bed mounts. Then right in front of the rear bed mounts. I can draw up a sketch but just wondering if it can be done and any ideas on how.

Steel plate and gussets is what I was thinking. Sketch coming tomorrow.

Alternatively, if I have to step notch instead, what do I do with my crossmember?

SCOTI · 06-08-2010, 07:52 PM

Yes, it can be done..... http://67-72chevytrucks.com/vboard/s...d.php?t=381425

Malibob · 06-08-2010, 09:36 PM

You sir are a bas ass! That is exactly what I was going for.

Malibob · 06-08-2010, 10:11 PM

Quote:

Originally Posted by SCOTI

Yes, it can be done..... http://67-72chevytrucks.com/vboard/s...d.php?t=381425

Why did you relocate your axles? Correct me if I am wrong, but, if I move the entire sections that holds the bed mounts, crossmember, shock mounts and springs couldnt I keep the stock setup and still drop the hell out of the truck? The only geometry changing would be the axle. Right? The added c-notch is an awesome idea too, I like the combination.

SCOTI · 06-08-2010, 11:45 PM

Quote:

Originally Posted by Malibob

Why did you relocate your axles? Correct me if I am wrong, but, if I move the entire sections that holds the bed mounts, crossmember, shock mounts and springs couldnt I keep the stock setup and still drop the hell out of the truck? The only geometry changing would be the axle. Right? The added c-notch is an awesome idea too, I like the combination.

Because even @ a 6-8" drop, the axle C/L shifts forward due to the geometry of the truck-arms. I just compensated for that & the additional drop allows for more travel/drop. I like the wheels centered or slightly to the rear on these trucks so I set it up w/some room for adjustment.

06-08-2010, 07:33 PM	#1
Malibob Registered User Join Date: May 2009 Location: Pittsburgh Posts: 392	Z-ing a frame (REAR) Can you z the rear of the frame? What I am thinking is right behind the cab before the bed mounts. Then right in front of the rear bed mounts. I can draw up a sketch but just wondering if it can be done and any ideas on how. Steel plate and gussets is what I was thinking. Sketch coming tomorrow. Alternatively, if I have to step notch instead, what do I do with my crossmember? __________________ This statement was made possible by a grant from this station and continued support from viewers like you. Flickr

06-08-2010, 07:52 PM	#2
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,041	Re: Z-ing a frame (REAR) Yes, it can be done..... http://67-72chevytrucks.com/vboard/s...d.php?t=381425 __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

06-08-2010, 09:36 PM	#3
Malibob Registered User Join Date: May 2009 Location: Pittsburgh Posts: 392	Re: Z-ing a frame (REAR) You sir are a bas ass! That is exactly what I was going for. __________________ This statement was made possible by a grant from this station and continued support from viewers like you. Flickr



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.