The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 06-09-2010, 11:11 PM   #1
solo_0569
Registered User
 
solo_0569's Avatar
 
Join Date: May 2010
Location: mexia,tx
Posts: 6
454 in a 67

has anyone put 454 in a 67 with headers and mt ? if what type of mods do i need to do?

Last edited by solo_0569; 06-09-2010 at 11:17 PM.
solo_0569 is offline   Reply With Quote
Old 06-09-2010, 11:48 PM   #2
MONTE
Registered User
 
MONTE's Avatar
 
Join Date: Oct 2005
Location: Donna, Texas
Posts: 286
Re: 454 in a 67

I went with Solid motor mounts on my 68 and Hooker header Super Comps.
MONTE is offline   Reply With Quote
Old 06-10-2010, 12:49 AM   #3
mike67
Registered User
 
Join Date: May 2010
Location: Calgary, Alberta
Posts: 14
Re: 454 in a 67

Check out this link. These guys used 72 BB motor mounts in their 67 Panel.
http://www.classicheartbeat.com/panel_8.htm

Additionally I just bought a 1967 Stepside Shortbox with a 454 in it. The mounts in my truck look different than the ones above and as you can see from the picture the PO did not select the right headers and used a hammer to solve the problem.

At some point in the future I'd like to redo this setup so hopefully someone else can advise on which mounts / headers would be the best.

Not the full answer you were probably looking for but hope this helps a bit.
Attached Images
  
mike67 is offline   Reply With Quote
Old 06-10-2010, 12:56 AM   #4
mike67
Registered User
 
Join Date: May 2010
Location: Calgary, Alberta
Posts: 14
Re: 454 in a 67

I also found this picture. Not sure what type of headers these are but very nice clearance around the mount.
Attached Images
 
mike67 is offline   Reply With Quote
Old 06-10-2010, 09:44 AM   #5
Sinister
Between Trucks...
 
Sinister's Avatar
 
Join Date: Mar 2002
Location: Los Angeles, CA.
Posts: 3,830
Re: 454 in a 67

Quote:
Originally Posted by mike67 View Post
I also found this picture. Not sure what type of headers these are but very nice clearance around the mount.
That's a small block.
__________________
Beat it to fit,
Paint it to match...
Sinister is offline   Reply With Quote
Old 06-10-2010, 04:03 PM   #6
raycow
Registered User
 
Join Date: Mar 2003
Location: San Francisco, CA USA
Posts: 2,454
Re: 454 in a 67

Quote:
Originally Posted by mike67 View Post
The mounts in my truck look different than the ones above and as you can see from the picture the PO did not select the right headers and used a hammer to solve the problem.
The frame bracket in the header pic looks like it might be for a SB?

Ray

Last edited by raycow; 06-10-2010 at 04:13 PM.
raycow is offline   Reply With Quote
Old 06-10-2010, 04:34 PM   #7
solo_0569
Registered User
 
solo_0569's Avatar
 
Join Date: May 2010
Location: mexia,tx
Posts: 6
Re: 454 in a 67

got motor in on stock mounts but need to know about headers and will they work with the z bar for the clutch. Are do i have swap to an auto tranny.
Attached Images
 
solo_0569 is offline   Reply With Quote
Old 06-10-2010, 04:38 PM   #8
-dylan-(OO==|==OO)
I dont drive fast,, I fly low!
 
-dylan-(OO==|==OO)'s Avatar
 
Join Date: May 2010
Location: sheperdsville KY
Posts: 118
Re: 454 in a 67

its a bolt in swap.... u will just have to get the truck headers.... other than that it should be a bolt in swap .... good luck
__________________
____________
/_______\
(OO==||==OO)

67 GMC CUSTOM,72 GMC...65 chevelle...65 fastback mustang...75 VEGA...90 lx mustang...90 supercoupe...90 jeep wrangler...04 mach 1 mustang...06 toyota tacoma...08 nissan altima
-dylan-(OO==|==OO) is offline   Reply With Quote
Old 06-10-2010, 04:53 PM   #9
MONTE
Registered User
 
MONTE's Avatar
 
Join Date: Oct 2005
Location: Donna, Texas
Posts: 286
Re: 454 in a 67

Hooker Headers
Name:  IMG_0693.jpg
Views: 141
Size:  69.1 KB
MONTE is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:41 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com