Inline 6 Harmonic Balancer removal?? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

LandonL · 07-18-2010, 03:17 PM

I've got the removal tool, but I can't find a retainer nut or bolt holding the damn thing on, is there one? I don't wanna start pulling and mess anything up but I need to know. Any help quickly would be great!

Lee H · 07-18-2010, 03:38 PM

Many of these early engines came with press fit balancers the cranks were often later tapped for a bolt when rebuilt. Just check carefully before forcing it off.

68gmsee · 07-18-2010, 04:03 PM

That's correct... My 68 only had an indentation and when I had the crank out for rework I had the machine shop drill and tap for a crank bolt. Easier to reinstall that way.

raycow · 07-19-2010, 05:40 PM

If your crank is threaded, don't try using the stock bolt to pull the balancer on. It's a good way to strip the threads. Instead, use a piece of allthread and screw it into the crank by hand as far as it will go. Then use a nut and washer on the allthread to pull the balancer on. It helps if you grease the threads and both sides of the washer.

Ray

qksilver · 07-19-2010, 08:42 PM

Auto zone offers the correct tool for free rental.......just make sure the threads on the tool are not messed up

07-18-2010, 03:17 PM	#1
LandonL Registered User Join Date: Nov 2009 Location: Georgia Posts: 440	Inline 6 Harmonic Balancer removal?? I've got the removal tool, but I can't find a retainer nut or bolt holding the damn thing on, is there one? I don't wanna start pulling and mess anything up but I need to know. Any help quickly would be great! __________________ ---\| 1967 GMC Stepside \|-- 250 L6 .030 over ---\| 1985 Porsche 944/1 \|--- Build Thread: '67 GMC http://67-72chevytrucks.com/vboard/s...d.php?t=378640 Last edited by LandonL; 07-18-2010 at 03:17 PM.

07-18-2010, 03:38 PM	#2
Lee H Registered User Join Date: Jun 2010 Location: Upland Ca Posts: 4,142	Re: Inline 6 Harmonic Balancer removal?? Many of these early engines came with press fit balancers the cranks were often later tapped for a bolt when rebuilt. Just check carefully before forcing it off. __________________ 1972 C10 SWB, Air, PS, PB, 350/350THM. Second owner. 1965 Corvette roadster, 44K miles, 327/365 SHP, 4 speed, side exhaust, knockoffs, teak, second owner (bought in 1970), Have ALL numbers matching components. My frame off restoration thread: http://67-72chevytrucks.com/vboard/s...d.php?t=556703

07-18-2010, 04:03 PM	#3
68gmsee Active Member Join Date: Jul 2007 Location: Centrally located between Houston, Austin and Waco. BCS area. Posts: 7,947	Re: Inline 6 Harmonic Balancer removal?? That's correct... My 68 only had an indentation and when I had the crank out for rework I had the machine shop drill and tap for a crank bolt. Easier to reinstall that way.

07-19-2010, 05:40 PM	#4
raycow Registered User Join Date: Mar 2003 Location: San Francisco, CA USA Posts: 2,454	Re: Inline 6 Harmonic Balancer removal?? If your crank is threaded, don't try using the stock bolt to pull the balancer on. It's a good way to strip the threads. Instead, use a piece of allthread and screw it into the crank by hand as far as it will go. Then use a nut and washer on the allthread to pull the balancer on. It helps if you grease the threads and both sides of the washer. Ray Last edited by raycow; 07-20-2010 at 01:27 AM.

07-19-2010, 08:42 PM	#5
qksilver Senior Member Join Date: Dec 2004 Location: Southern Pines NC Posts: 3,853	Re: Inline 6 Harmonic Balancer removal?? Auto zone offers the correct tool for free rental.......just make sure the threads on the tool are not messed up



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.