traded a pellet rifle for a 350 today - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Davetopay · 07-20-2010, 06:14 PM

Any ridge in the top of the cylinder? If not, a simple dingle hone and some new rings will be fine.

Was there any info stamped on the nose of the cam?

71GMCinTN · 07-20-2010, 08:01 PM

Well, just went out to check again, and there is a slight ridge. Figured as soon as I was able to see the cam nose, the numbers would be right there. Actually the nose looks rough (made like that I reckon) has a CC (one C stagerd over the top of the other C) and a 2 * 8 H (real rough where the middle number should be) Other numbers on the rear but can't make out all. Like 12 210 and 6698 across the bottom.

71GMCinTN · 07-20-2010, 08:04 PM

Hmm. Didn't think about the ridge the other day. Better to bore it .040 if there is any ridge at all? (think I know the answer)

Davetopay · 07-20-2010, 08:31 PM

Quote:

Originally Posted by 71GMCinTN

Hmm. Didn't think about the ridge the other day. Better to bore it .040 if there is any ridge at all? (think I know the answer)

Or...if you screw it back together and it squeezes decent compression, leave it be.

As for the cam...."CC"? Crane Cams? 2*8?....268, 288..those were grinds for chevys. Under the Crane Blazer series they had the 288H.

Crane H268 206*/206* @.050 268/268* adv. 112LSA, .448/.448 lift
rpm range 1500-4000

Crane Blazer H288 226*/234*@.050 288/296adv 114LSA .458/.473 (1.5 rocker) (this is technically a Pontiac grind, still looking for chevy numbers.)

Most info on an H288 Crane cam points to a solid lifter cam. I'd be willing to bet you have a 268.

crushermechanic · 07-20-2010, 08:44 PM

it is a comp cam high energy 268. the 12-210 is the part #. if you need a good machinist in nashville pm me and i will give you a # to a very good one.

**JDL** · 07-20-2010, 08:45 PM

Code Year CID Vehicle HP RPO Trans Carb Comments
CMR 74 350 Chevelle 145 L-65 T-H 400 2-Brl
CMR 78 350 Corvette 220 L-82 TH 350 4-Brl
CMR 80 305 Impala 155 LG-4 TH 350 4-Brl

This may help

Huck · 07-21-2010, 08:48 AM

Way clean on the inside with blue head gasket material---not original---must have been a refresh at some time.
The RWS pellet guns are great--got any more--I have a 350---010. in the barn just hankering to trade for a RWS??? hehehehe

71GMCinTN · 07-21-2010, 08:52 AM

Was the only one I had Huck. Deff. was rebuilt, and bored .030 over. Was just surprized at how clean it was inside, considering it was FILTHY on the outside.

oldblue1968chevy · 07-21-2010, 09:54 AM

wonder if my filthy late 70's motor looks like this..probably not LOL

07-20-2010, 06:14 PM	#26
Davetopay Registered User Join Date: Oct 2009 Location: Leesburg, VA Posts: 424	Re: traded a pellet rifle for a 350 today Any ridge in the top of the cylinder? If not, a simple dingle hone and some new rings will be fine. Was there any info stamped on the nose of the cam?

07-20-2010, 08:01 PM	#27
71GMCinTN Registered User Join Date: Jul 2010 Location: Nashville TN Posts: 52	Re: traded a pellet rifle for a 350 today Well, just went out to check again, and there is a slight ridge. Figured as soon as I was able to see the cam nose, the numbers would be right there. Actually the nose looks rough (made like that I reckon) has a CC (one C stagerd over the top of the other C) and a 2 * 8 H (real rough where the middle number should be) Other numbers on the rear but can't make out all. Like 12 210 and 6698 across the bottom. Last edited by 71GMCinTN; 07-20-2010 at 08:02 PM.

07-20-2010, 08:04 PM	#28
71GMCinTN Registered User Join Date: Jul 2010 Location: Nashville TN Posts: 52	Re: traded a pellet rifle for a 350 today Hmm. Didn't think about the ridge the other day. Better to bore it .040 if there is any ridge at all? (think I know the answer)

07-20-2010, 08:44 PM	#30
crushermechanic Registered User Join Date: Dec 2009 Location: Fort Walton Beach, Fl Posts: 357	Re: traded a pellet rifle for a 350 today it is a comp cam high energy 268. the 12-210 is the part #. if you need a good machinist in nashville pm me and i will give you a # to a very good one.

07-20-2010, 08:45 PM	#31
JDL Senior Member Join Date: Sep 2000 Location: Agency IA. Posts: 1,839	Re: traded a pellet rifle for a 350 today Code Year CID Vehicle HP RPO Trans Carb Comments CMR 74 350 Chevelle 145 L-65 T-H 400 2-Brl CMR 78 350 Corvette 220 L-82 TH 350 4-Brl CMR 80 305 Impala 155 LG-4 TH 350 4-Brl This may help __________________ 72 Chevy short step side with 454 air and tilt. 72 nova project car 63 chevy II drag car Agency Iowa

07-21-2010, 08:48 AM	#32
Huck Senior Member Join Date: Jun 2001 Location: Shelbyville, KY Posts: 3,269	Re: traded a pellet rifle for a 350 today Way clean on the inside with blue head gasket material---not original---must have been a refresh at some time. The RWS pellet guns are great--got any more--I have a 350---010. in the barn just hankering to trade for a RWS??? hehehehe

07-21-2010, 08:52 AM	#33
71GMCinTN Registered User Join Date: Jul 2010 Location: Nashville TN Posts: 52	Re: traded a pellet rifle for a 350 today Was the only one I had Huck. Deff. was rebuilt, and bored .030 over. Was just surprized at how clean it was inside, considering it was FILTHY on the outside. Last edited by 71GMCinTN; 07-21-2010 at 09:14 AM.

07-21-2010, 09:54 AM	#34
oldblue1968chevy Grandpa in the rustmobile... Join Date: Nov 2008 Location: Spokane WA/Viola TN Posts: 11,422	Re: traded a pellet rifle for a 350 today wonder if my filthy late 70's motor looks like this..probably not LOL __________________ John Goose-1968 C10 355,9.32-1CR, Vortec Heads ,262 voodoo, 3.73:1 3OTT (HS ride/beater/farm truck) http://67-72chevytrucks.com/vboard/s...d.php?t=317684 Grams 53-1953 Chevrolet Belair http://67-72chevytrucks.com/vboard/s...=1#post4327784 1969 Chevy C10 Shortbed 4.5/6?" Frame off resto http://67-72chevytrucks.com/vboard/s...d.php?t=548136 1999 Toyota Tacoma 4x4



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.