Dana 44 oil seal replacement - The 1947 - Present Chevrolet & GMC Truck Message Board Network

69-72 · 08-04-2010, 10:22 PM

It appears that I have one side of my front axle leaking. From what I can figure I will need to replace the seals in the middle of the axle. What else should I consider replacing while I have it all apart?

I don't really 4x4 much, just put it on in the winter from time to time and the Blazer is pretty original, I doubt that the 4x4 was used much before I got it.

BERT306 · 08-04-2010, 10:36 PM

I'd replace the u joints on the axle shafts while it was apart

LONGHAIR · 08-05-2010, 06:14 AM

I would take a good look at the bearing inside the spindle too. There is no way to service them w/o disassembly, so they get ignored.

SeventyOne · 08-08-2010, 02:29 PM

This would be the time to regear if you have been considering it.

**D.PASSMORE** · 08-09-2010, 10:42 PM

You can get the seals from a local parts store. Its the same PN for all 1/2t, D-44 front axles. Chicago Rawhide (CR) makes them and be aware that the crosses in your outer axles will have to be taken to the parts store and matched up. Sometime in '72, GM started putting larger crosses in the outer axles and the only sure way to know is remove and take with you. Hope this helps.

Oh yeah, don't jack the slingers up, they are to find these days.

08-04-2010, 10:22 PM	#1
69-72 Registered User Join Date: May 2008 Location: 204 Posts: 903	Dana 44 oil seal replacement It appears that I have one side of my front axle leaking. From what I can figure I will need to replace the seals in the middle of the axle. What else should I consider replacing while I have it all apart? I don't really 4x4 much, just put it on in the winter from time to time and the Blazer is pretty original, I doubt that the 4x4 was used much before I got it. __________________ 1969 Chevy Custom Camper 3/4 ton Rust free survivor 1972 Chevy Blazer CST 4x4 Almost Rust free survivor 1972 GMC Jimmy 2wd Undergoing surgery

08-04-2010, 10:36 PM	#2
BERT306 Registered User Join Date: Jul 2005 Location: Steeleville IL Posts: 72	Re: Dana 44 oil seal replacement I'd replace the u joints on the axle shafts while it was apart __________________ 72 k10 swb. 350/th350/np205. Vintage air'd daily driver

08-08-2010, 02:29 PM	#4
SeventyOne Registered User Join Date: Mar 2007 Location: Oakland, Ca Posts: 1,381	Re: Dana 44 oil seal replacement This would be the time to regear if you have been considering it.

08-09-2010, 10:42 PM	#5
D.PASSMORE One of the First Join Date: Jan 2000 Location: St. Augustine,FL. Posts: 4,055	Re: Dana 44 oil seal replacement You can get the seals from a local parts store. Its the same PN for all 1/2t, D-44 front axles. Chicago Rawhide (CR) makes them and be aware that the crosses in your outer axles will have to be taken to the parts store and matched up. Sometime in '72, GM started putting larger crosses in the outer axles and the only sure way to know is remove and take with you. Hope this helps. Oh yeah, don't jack the slingers up, they are to find these days. __________________ DAVID PASSMORE ST AUGUSTINE ,FL ZIP 32084 '71 SWB K/10 CUSTOM DELUXE (Chili) '72 BLAZER K/5 Muscle Truck (Mule) '72 LWB K/20 CHEYENNE (Blackie) Last edited by D.PASSMORE; 08-09-2010 at 10:44 PM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.