|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
09-05-2010, 09:17 PM
|
#1 |
|
Senior Member
 Join Date: Jun 2010
Location: Orlando, Florida
Posts: 2,509
|
putting 68 396 into 71 c10
Will a 396 automatic out of a 68 3/4 ton truck work in my 71 c10? Could I just use the mounting hardware out of the 68? Didn't know if there were frame differences with the donor truck being a 3/4 ton and a 68.
Thanks!
__________________
71 Chevy C10 Shortbed Stepside. LT1 with 4l60E. Just got back from painter, in assembly now. |
|
|
|
09-05-2010, 10:10 PM
|
#2 |
|
Senior Member
Join Date: Nov 2003
Location: Brookings, SD
Posts: 10,497
|
Re: putting 68 396 into 71 c10
It will bolt up for the most part. Make sure you grab the frame towers for the engine mounts, those are big block specific.
__________________
Some people are like slinkies, they aren't good for anything, but you can't help but smile when you see one tumble down the stairs. |
|
|
|
|
09-05-2010, 10:11 PM
|
#3 |
|
Senior Member
Join Date: Jun 2010
Location: Orlando, Florida
Posts: 2,509
|
Re: putting 68 396 into 71 c10
So if I have the donor truck, I should have everything I need? Will this motor run on regular or will it need premium?
__________________
71 Chevy C10 Shortbed Stepside. LT1 with 4l60E. Just got back from painter, in assembly now. |
|
|
|
|
09-05-2010, 10:17 PM
|
#4 |
|
Junior Member
Join Date: Dec 2006
Location: Southeast Missouri
Posts: 2,436
|
Re: putting 68 396 into 71 c10
Is the engine stock, if it is regular will be ok depending on how far the timing is advanced.
I have '73 454 and it runs ok on regular gasoline.
__________________
'67 Chevy C-20 short stepper - build complete, 454/SM-465. '75 C-30 Single Cab DRW-350 small block/NP-435. '77 GMC-6500 Dump Truck, 427 Tall Deck. '92 GMC K-3500 Duallie, 454/4L80E. |
|
|
|
|
09-05-2010, 10:19 PM
|
#5 |
|
Senior Member
Join Date: Jun 2010
Location: Orlando, Florida
Posts: 2,509
|
Re: putting 68 396 into 71 c10
I'm pretty sure it's stock. Still has qjet and cast iron manifolds.
__________________
71 Chevy C10 Shortbed Stepside. LT1 with 4l60E. Just got back from painter, in assembly now. |
|
|
|
|
09-05-2010, 10:25 PM
|
#6 | ||
|
Gone to greener pastures
Join Date: May 2007
Location: Gateway to the Delta
Posts: 7,354
|
Re: putting 68 396 into 71 c10
Quote:
Quote:
My 402 runs just fine on 87 octane.
__________________
'69 Chevy 1/2 T LWB Stepper: Daily Beater '72 GMC 3/4 T Fleet: Another Daily Beater '72 Plymouth Gran Coupe: ? "Ah women. They make the highs higher and the lows more frequent." Friedrich Nietzsche "Never kick a fresh turd on a hot day." Harry S. Truman GUN CONTROL: Never having to say, "I missed you." Always fire two warning shots into your attacker's chest area before putting a bullet between his eyes. Paraphrased from Louis Awerbuck |
||
|
|
|
|
09-05-2010, 10:34 PM
|
#7 |
|
Junior Member
Join Date: Dec 2006
Location: Southeast Missouri
Posts: 2,436
|
Re: putting 68 396 into 71 c10
I would put a can of SeaFoam in the gas tank with the next fill-up. I usually do that when an engine has not been ran for a while. Most auto parts stores carry it.
__________________
'67 Chevy C-20 short stepper - build complete, 454/SM-465. '75 C-30 Single Cab DRW-350 small block/NP-435. '77 GMC-6500 Dump Truck, 427 Tall Deck. '92 GMC K-3500 Duallie, 454/4L80E. |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
