![]() |
|
![]() |
#1 | |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,856
|
Re: PO has me PO'd
Quote:
![]() ![]() plus. plus it was only 100 bucks at Harbour Freight
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; 12-01-2010 at 12:46 AM. |
|
![]() |
![]() |
![]() |
#2 | |
Registered User
Join Date: Oct 2007
Location: Spanaway
Posts: 8,451
|
Re: PO has me PO'd
Quote:
![]()
__________________
Mike. Swamp Rat build thread : http://67-72chevytrucks.com/vboard/s...d.php?t=595019 72 3/4T 4X4 4" BDS Lift 33" BFG's |
|
![]() |
![]() |
![]() |
#3 |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,856
|
Re: PO has me PO'd
sorry, just playin with the photobucket, problems downloadin
![]() ![]() tool I used to get the second roll pin started ![]() front wheel drive only ![]()
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; 12-08-2010 at 02:32 AM. |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Oct 2003
Location: Central Vermont
Posts: 8,537
|
Re: PO has me PO'd
Your going to love the twin stick, comes in handy...a lot!
|
![]() |
![]() |
![]() |
#5 |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,856
|
Re: PO has me PO'd
thanks Kurt, saw you use it alot, and had to have one
![]() used some exhaust manifold studs to help get things aligned, don't forget to put it in gear and rotate the tailshaft, don't ask how I know... ![]() ![]() problem with the passenger side diagonal brace on the crossmember, need to cut a 1 1/2" square to clear the pivot bolt
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; 12-08-2010 at 04:54 PM. |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Oct 2003
Location: Central Vermont
Posts: 8,537
|
Re: PO has me PO'd
Just make sure the rear of the 205 is mounted correctly, ask me how I know.
![]() |
![]() |
![]() |
![]() |
#7 | |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,856
|
Re: PO has me PO'd
Quote:
![]() are you referring to the side mount, when you state that it needs to be properly mounted???
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
|
![]() |
![]() |
![]() |
Bookmarks |
|
|