Paint Bubbles... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Canadian694x4** · 06-25-2003, 08:08 PM

Well when I bought my truck, in the lower front door panel there were 2 paint bubbles and I now have noticed the last time I washed the truck that it is starting to ooze rusty colored liquid.

How do I repair or put a temp fix on this? I want to do sumthin before it possbily rots out the bottom of the door. I'm not ready to paint the truck, but that could possbily happen this winter...

Any help would be great

Thanks

Brian

71GMC_3/4T · 06-25-2003, 08:18 PM

The first thing you should do is check your drain holes in your doors. Clean 'em out real well, remove the door panel if you have to and shop vac out all the crap. While you're in there, look around for any signs of body work or rust from the inside.
If it was me, I'd think about cutting itty bitty holes in the bottoms of the bubbles to let any water out that may have gotten in there.

mtdave2 · 06-25-2003, 08:56 PM

i had bubbles in my tool box door. i started to scrape them a bit.....long story short.. the whole bottom of the door was full of rust. im repainting the door now... bubbles= not good.

progress · 06-25-2003, 10:26 PM

If there is a bubble...there is rust underneath. Scrape it off and sand it all down. Once you fix the door drains you will have to take it to bare metal, prime and paint. If it is a small spot you can do a decent repair, feather and buff. When you get around to doing your entire truck it will not have gotten any worse. If you wait until you are going to repaint you might have to reskin the door or even get a new one if the bottom is rusted out.

Even if you shake and spray it...it will be better than letting it go and get worse.

ginter · 06-25-2003, 11:46 PM

Quote:

If there is a bubble...there is rust underneath. Scrape it off and sand it all down. Once you fix the door drains you will have to take it to bare metal, prime and paint. If it is a small spot you can do a decent repair, feather and buff. When you get around to doing your entire truck it will not have gotten any worse. If you wait until you are going to repaint you might have to reskin the door or even get a new one if the bottom is rusted out.

Even if you shake and spray it...it will be better than letting it go and get worse.

Couldn't have said it better myself. Where there are bubbles, there is rust. The sooner you do something with it (if it's not too late already) the better off you'll be. I'm doing some rust repair on a car right now. Everywhere there were even little bubbles under the paint that hadn't come through yet, when I sanded the paint off (and the rust) there was nothing but hole when I was finished.

06-25-2003, 08:08 PM	#1
Canadian694x4 Born To Lose Club Join Date: Feb 2003 Location: Calgary, Alberta/Oxenden, Ontario, Great White North Posts: 13,307	Paint Bubbles... Well when I bought my truck, in the lower front door panel there were 2 paint bubbles and I now have noticed the last time I washed the truck that it is starting to ooze rusty colored liquid. How do I repair or put a temp fix on this? I want to do sumthin before it possbily rots out the bottom of the door. I'm not ready to paint the truck, but that could possbily happen this winter... Any help would be great Thanks Brian __________________ Brian Smith - "Born To Lose" 1969 Chevrolet K10 LWB Fleetside - Proud Owner For 22 Yrs - 1 of 208 Built & Sold In Canada!- 283 V8/350TH/NP208, 2" All Spring Lift, 32" Good Year MT/R's. 1972 GMC K2500 Custom LWB Fleetside - Proud Owner For 3 Yrs - 1 of 571 Built & Sold In Canada! - 350 V8/SM465/NP205, 4” Rough Country Lift, 33” Interco TSL Thornbirds 2007.5 GMC Sierra SLE 2500HD 4x4 - Proud Owner For 17 Yrs- 6.6L V8 Duramax Diesel/Allison 1000, 2" Lift, 33" Mickey Thompson MTZ's. 2008 Yamaha Raptor 700r - Proud Owner For 15 Yrs - ITP Mud Lites. 2015 John Deere 1025R - Proud Owner For 8 Yrs - 24HP Diesel/H120/54D/260B/SB1154.

06-25-2003, 08:18 PM	#2
71GMC_3/4T Weapons Of Construction Join Date: Apr 2000 Location: Colorado, USA Posts: 1,095	The first thing you should do is check your drain holes in your doors. Clean 'em out real well, remove the door panel if you have to and shop vac out all the crap. While you're in there, look around for any signs of body work or rust from the inside. If it was me, I'd think about cutting itty bitty holes in the bottoms of the bubbles to let any water out that may have gotten in there. __________________ 1971 GMC 2500, 402/TH400 4.10 Daily Driver Lafayette, CO

06-25-2003, 08:56 PM	#3
mtdave2 newly minted old timer Join Date: Dec 1999 Location: Hudson WI Posts: 3,521	i had bubbles in my tool box door. i started to scrape them a bit.....long story short.. the whole bottom of the door was full of rust. im repainting the door now... bubbles= not good. __________________ ____________________________________________ 72 c20 longhorn 65k org miles and counting! 69 k10 Suburban

06-25-2003, 10:26 PM	#4
progress Gotta luv a clean shave Join Date: Jan 2002 Location: Kent, WA Posts: 226	If there is a bubble...there is rust underneath. Scrape it off and sand it all down. Once you fix the door drains you will have to take it to bare metal, prime and paint. If it is a small spot you can do a decent repair, feather and buff. When you get around to doing your entire truck it will not have gotten any worse. If you wait until you are going to repaint you might have to reskin the door or even get a new one if the bottom is rusted out. Even if you shake and spray it...it will be better than letting it go and get worse. __________________ Welding while you wait...you can help if you like and it...might even save you a little as long as you don't mess things up! We make house calls too...just like the old days! Last edited by progress; 06-25-2003 at 10:32 PM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.