|
07-02-2003, 08:25 AM
|
#1 |
|
Registered User
Join Date: Apr 2000
Location: Camillus, NY USA
Posts: 79
|
Starter Shims
Anybody know the "Proper" amount to shim a starter?
I've got a new standard size starter on my 350 Auto. Too much noise when the starter engages, so I suspect it's not shimmed right. David 
__________________
1972 Chevy Cheyenne Super LWB Chevy Red/White with rally wheels. Not-so-Stock 350, A/T, A/C, tilt. Vroom, Vroom.... ===================== David Colbert dcolbert@twcny.rr.com Work hard, play harder! |
|
|
|
07-02-2003, 08:50 AM
|
#2 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,403
|
If you slide a 1/8" checker rod(pc welding rod will do), between the OD of the flex plate, & the arma ture shaft you can shim accordingly. If the meaure is too tight, you need to use the shims under both bolts......if its too loose, you need to cut the shims in half, & shim the outer bolt only. just use the 1/8" rod as a feeler guage(not loose, but not tight). Many of the reman starters come with this checker rod. Good luck,crazyL
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
|
|
|
|
07-02-2003, 01:33 PM
|
#3 |
|
Registered User
Join Date: Apr 2000
Location: Camillus, NY USA
Posts: 79
|
Hmmm. I've never seen or heard of a checker rod before. Sounds like a good idea though. I wonder if I can use a #1 phillips driver instead.
Is the procedure the same for starters with offset bolt patterns? David
__________________
1972 Chevy Cheyenne Super LWB Chevy Red/White with rally wheels. Not-so-Stock 350, A/T, A/C, tilt. Vroom, Vroom.... ===================== David Colbert dcolbert@twcny.rr.com Work hard, play harder! |
|
|
|
|
07-02-2003, 01:39 PM
|
#4 |
|
Registered User
Join Date: Jul 2000
Location: NC
Posts: 987
|
Yes, the procedure is the same for the offset pattern. If the screwdriver is 1/8" in diameter. You could also use a 1/8" diameter drill bit.
|
|
|
|
|
07-07-2003, 08:58 AM
|
#5 |
|
Registered User
Join Date: Apr 2000
Location: Camillus, NY USA
Posts: 79
|
Drill bit idea worked good.
I took out the two thin shims that I had installed and have a clearance of about 5/32". Must have some wear on the fly wheel. Not surprising considering its age. Starter seems a little quieter and seems to have more torque. Amazing what a difference a 1/16th of an inch can make. Thanks for your help guys! David
__________________
1972 Chevy Cheyenne Super LWB Chevy Red/White with rally wheels. Not-so-Stock 350, A/T, A/C, tilt. Vroom, Vroom.... ===================== David Colbert dcolbert@twcny.rr.com Work hard, play harder! |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
