head help - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Patch** · 07-04-2003, 06:08 PM

Hi there... I need some help knowing which set of heads to use.....I have 2 sets...both magged and good to go....
the 1st set #'s are 14101083
The 2nd set is 14102193
this is going on a factory replacement motor.....just wondering if anyone knew which set was better? Thanks........

mooneyes · 07-04-2003, 07:07 PM

.....only info i have is the 14101083 is 87 and up 350 64 cc chambers...and the 14102193 all i have is 87 and up 350..so i'm guessing there pretty much the same heads

**Patch** · 07-05-2003, 11:32 AM

So it appears that there both 64 cc heads?

**Patch** · 07-07-2003, 03:13 AM

The one set has round push rod holes...and from what I'm understanding, these need self aligning rockers....the other set of heads have almost a rectangle shaped push rod hole...can these take normal rockers? Thanks again......

Longhorn Man · 07-07-2003, 07:07 AM

being that they are both 87 and up, You'll probably need the vortec intake, self alighning rockers, and centerbolt covers.

*racedvl* · 07-07-2003, 09:28 AM

Quote:

Originally posted by longhornmail
being that they are both 87 and up, You'll probably need the vortec intake, self alighning rockers, and centerbolt covers.

Only if they are 96 and up Vortec heads. You will need the center bolt covers though.

Longhorn Man · 07-07-2003, 03:40 PM

DOH! Thanks, Jason.

*racedvl* · 07-07-2003, 04:30 PM

07-04-2003, 06:08 PM	#1
Patch Senior Member Join Date: Jul 2002 Location: Oak Harbor, WA Posts: 706	head help Hi there... I need some help knowing which set of heads to use.....I have 2 sets...both magged and good to go.... the 1st set #'s are 14101083 The 2nd set is 14102193 this is going on a factory replacement motor.....just wondering if anyone knew which set was better? Thanks........ __________________ Patch

07-04-2003, 07:07 PM	#2
mooneyes Registered User Join Date: Jan 2002 Location: Slippery Rock PA USA Posts: 1,692	.....only info i have is the 14101083 is 87 and up 350 64 cc chambers...and the 14102193 all i have is 87 and up 350..so i'm guessing there pretty much the same heads __________________ Ken Lyons, Slippery rock pa 68 short step 327 t10 4 gear 72 2wd blazer project 70 lwb 305/700r driver 78 caprice project 02 cavalier D.D ( hate it!!)

07-05-2003, 11:32 AM	#3
Patch Senior Member Join Date: Jul 2002 Location: Oak Harbor, WA Posts: 706	Thanks So it appears that there both 64 cc heads? __________________ Patch

07-07-2003, 03:13 AM	#4
Patch Senior Member Join Date: Jul 2002 Location: Oak Harbor, WA Posts: 706	Rockers? The one set has round push rod holes...and from what I'm understanding, these need self aligning rockers....the other set of heads have almost a rectangle shaped push rod hole...can these take normal rockers? Thanks again...... __________________ Patch

07-07-2003, 07:07 AM	#5
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	being that they are both 87 and up, You'll probably need the vortec intake, self alighning rockers, and centerbolt covers.

07-07-2003, 03:40 PM	#7
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	DOH! Thanks, Jason.

07-07-2003, 04:30 PM	#8
racedvl Account Suspended Join Date: Jan 2000 Location: Woodstock, IL Posts: 7,020



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.